CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
Tech Tips
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the 6 hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
INSTALL FRONT SEAT WIRE RH (for Front Passenger Side with Occupant Classification System)
Connect each connector and engage each clamp to install the front seat wire RH.
INSTALL FRONT SEAT WIRE
Connect each connector and engage each clamp to install the front seat wire.
INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Engage the 3 claws and guide to install the front seat cushion edge protector LH.
INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
Engage the clip (B) to install the front seat lower cushion shield LH.
Engage the hook.
Engage the clip (A).
INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Engage the clip to install the front seat lower cushion shield RH.
Engage the hook.
Install the screw.
INSTALL SEAT CUSHION CLIMATE CONTROL BLOWER ASSEMBLY (w/ Climate Control Seat System)
Install the seat cushion climate control blower assembly.
Connect the connector.
INSTALL SEAT CUSHION CLIMATE CONTROL BRACKET (w/ Climate Control Seat System)
Using a T20 "TORX" socket wrench, install the seat cushion climate control bracket to the seat cushion climate control blower assembly with the 2 screws.
INSTALL SEAT CUSHION CLIMATE CONTROL DUCT (w/ Climate Control Seat System)
Engage the 2 claws to install the seat cushion climate control duct to the seat cushion climate control blower assembly.
INSTALL FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (for Front Passenger Side)
INSTALL FRONT SEAT VERTICAL ADJUSTER ASSEMBLY (w/ Variable Seat Cushion System)
Engage the clamp.
Connect the connector.
Install the front seat vertical adjuster assembly with the 4 nuts.
INSTALL SEAT COVER WIRE (for Standard Seat Type)
Install the 6 seat cover wires.
Tech Tips
Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.
For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.
Make sure to read the precautions before preparing the wire.
Length | ||||||||
---|---|---|---|---|---|---|---|---|
|
Tech Tips
The dimensions shown in the illustration are the length.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER (for Standard Seat Type)
Tech Tips
When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order indicated in the illustration.
Note
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
w/o Variable Seat Cushion System:
Using hog ring pliers, install 6 new hog rings in the order indicated in the illustration.
Note
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
w/ Variable Seat Cushion System:
Using hog ring pliers, install 2 new hog rings in the order indicated in the illustration.
Note
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Standard Seat Type)
w/o Variable Seat Cushion System:
Engage the 10 hooks to install the separate type front seat cushion cover with pad.
w/ Variable Seat Cushion System:
Engage the 7 hooks to install the separate type front seat cushion cover with pad.
Using hog ring pliers, install 4 new hog rings in the order indicated in the illustration.
Note
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Engage the 4 hooks.
Fastener |
Engage the 2 fasteners.
for Front Passenger Side without Occupant Classification System:
Engage the claw to install the connector.
Connect the connector.
w/ Seat Heater System:
Engage the 4 clamps.
Connect the connector.
INSTALL FRONT SEAT CUSHION PAD WITH COVER (for Sports Seat Type)
Engage the 10 hooks to install the separate type front seat cushion pad with cover.
for Front Passenger Side without Occupant Classification System:
Engage the claw to install the connector.
Connect the connector.
w/ Seat Heater System:
Engage the 4 clamps.
Connect the connector.
INSTALL FRONT SEAT NO. 2 WIRE
Connect each connector and engage each clamp to install the front seat No. 2 wire.
INSTALL SEATBACK CLIMATE CONTROL BLOWER (w/ Climate Control Seat System)
Engage the 2 clips to install the seatback climate control blower.
Connect the connector.
INSTALL FRONT SEATBACK HOOK
Install the 2 front seatback hooks to the lumbar support adjuster assembly.
INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY
INSTALL FRONT SEATBACK EDGE PROTECTOR
Engage each claw to install the 2 front seatback edge protectors.
INSTALL FRONT SEAT AIRBAG ASSEMBLY
INSTALL SEATBACK FELT
*1 | Front Seat Airbag Assembly |
*a | Wire on Back of Front Seatback Frame Sub-assembly |
Install the seatback felt.
Note
Make sure to pass the front seat airbag assembly and the wire on the back of the front seatback frame sub-assembly through the seatback felt.
INSTALL TELEVISION BASE (w/ Rear Seat Entertainment System)
Engage the clamp.
Engage the 2 guides.
Install the television base with the 2 screws.
INSTALL SEAT COVER WIRE (for Standard Seat Type)
Install the 5 seat cover wires.
Tech Tips
Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.
For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.
Make sure to read the precautions before preparing the wire.
Length | ||||||
---|---|---|---|---|---|---|
|
Tech Tips
The dimensions shown in the illustration are the length.
INSTALL SEPARATE TYPE FRONT SEATBACK COVER (for Standard Seat Type)
Tech Tips
When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 12 new hog rings in the order indicated in the illustration.
Note
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Standard Seat Type)
Install the separate type front seatback cover with pad.
w/ Rear Seat Entertainment System:
Install the 11 clips.
*a | Bracket |
Engage the 3 brackets and install the 2 nuts.
Note
For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the brackets securely.
INSTALL FRONT SEATBACK PAD WITH COVER (for Sports Seat Type)
Install the front seatback pad with cover.
*a | Bracket |
Engage the 2 brackets and install the 2 nuts.
Note
For vehicles with a front seat airbag assembly, the front seatback pad with cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the brackets securely.
INSTALL FRONT SEAT HEADREST SUPPORT
Engage each claw to install the 2 front seat headrest supports.
Engage the 10 hooks.
w/ Climate Control Seat System:
Engage the 2 claws to install the seatback climate control blower.
w/ Rear Seat Entertainment System:
Engage the clamp to install the front seat No. 2 wire.
Engage the clamp to install the front seat No. 2 wire.
Fastener |
Engage the 2 fasteners.
INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY
Engage the 2 hooks to install the front seatback board sub-assembly.
Install the 2 screws.
INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the 4 guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Install the 4 bolts.
w/ Rear Seat Entertainment System:
Engage the 2 claws and 4 clamps to install the front seat No. 2 wire.
Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.
Tech Tips
Engage the claw first.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
w/ Rear Seat Entertainment System:
Engage the clamp.
Fastener |
Engage the fastener to secure the front seat airbag assembly wire harness.
Engage the clamp.
Connect the connector.
Engage the 3 hooks.
INSTALL SEAT VARIABLE CUSHION SWITCH (w/ Variable Seat Cushion System)
INSTALL FRONT LUMBAR POWER SEAT SWITCH
INSTALL FRONT POWER SEAT SWITCH (w/o Seat Position Memory System)
INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Position Memory System)
INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the 4 claws to install the reclining power seat switch knob.
INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the 4 claws to install the slide and vertical power seat switch knob.
INSTALL FRONT SEAT INNER CUSHION SHIELD
Engage the claw and guide to install the front seat inner cushion shield.
Engage the claw and 3 guides.
INSTALL INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Standard Seat Type)
Engage the claw and clip to install the inner No. 1 front seat cushion shield.
w/ Variable Seat Cushion System:
Engage the hook.
Engage the clamp.
Install the 2 screws.
INSTALL FRONT SEAT CUSHION SHIELD (for Standard Seat Type)
Connect the front lumbar power seat switch connector.
w/o Seat Position Memory System:
Connect the front power seat switch connector.
w/ Seat Position Memory System:
Connect the 2 position control ECU and switch assembly connectors.
w/ Variable Seat Cushion System:
Connect the seat variable cushion switch connector.
Engage the 3 claws to close the wire harness cover.
Wire Harness Guide |
Install the wire harness to the wire harness guide.
Engage the 2 clamps.
Engage the 3 claws.
Engage the clip and 2 guides to install the front seat cushion shield.
Engage the claw and 3 guides.
INSTALL FRONT SEAT CUSHION SHIELD (for Sports Seat Type)
Connect the front lumbar power seat switch connector.
w/o Seat Position Memory System:
Connect the front power seat switch connector.
w/ Seat Position Memory System:
Connect the 2 position control ECU and switch assembly connectors.
Engage the 3 claws to close the wire harness cover.
Wire Harness Guide |
Install the wire harness to the wire harness guide.
Engage the 2 clamps.
Engage the clip and 2 guides to install the front seat cushion shield.
Engage the claw and 3 guides.
INSTALL INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Sports Seat Type)
Engage the clamp.
Install the clip to the inner No. 1 front seat cushion shield.
Engage the 3 guides to install the inner No. 1 front seat cushion shield.
Slide |
Engage the 2 claws as shown in the illustration.
Engage the claw.
Engage the clip.
Install the screw.
CONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY
Connect the 2 rubber bands of the front seatback board sub-assembly.
INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
INSTALL OCCUPANT DETECTION ECU (for Front Passenger Side with Occupant Classification System)
INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)