OIL AND OIL FILTER REPLACEMENT
CAUTION / NOTICE / HINT
Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.
PROCEDURE
REMOVE OIL FILTER ELEMENT SERVICE HOLE COVER (for Full Cover Type)
-
Remove the 8 clips and fold back the oil filter element service hole cover.
Tip:It is not necessary to fully remove the No. 1 engine under cover. Partially remove it so that the oil filter element can be removed in a later step.
-
DRAIN ENGINE OIL
Remove the oil filler cap.
Remove the oil pan drain plug and gasket, and drain the engine oil into a container.
Clean the oil pan drain plug.
Install a new gasket to the oil pan drain plug.
Install the oil pan drain plug.
38 N*m
387 kgf*cm
28 ft.*lbf
REMOVE OIL FILTER ELEMENT
-
*a
Oil Filter Bracket Clip
*b
Cap Rib
Using SST, loosen the oil filter cap assembly 4 turns, align the cap ribs vertically, and drain the remaining engine oil from the oil filter cap assembly.
09228-06501
Note:Do not remove the oil filter bracket clip when removing the oil filter cap assembly.
Tip:Set a container below the oil filter cap assembly before loosening the oil filter cap assembly.
-
*1
Oil Filter Element
*2
O-ring
*3
Oil Filter Cap Assembly
Remove the oil filter element and O-ring from the oil filter cap assembly.
Note:Do not use any tools to remove the O-ring in order to prevent the oil filter cap assembly from being damaged. Be sure to remove it by hand.
-
INSTALL OIL FILTER ELEMENT
Clean the inside of the oil filter cap assembly, the threads and O-ring groove.
-
*1
O-ring
*a
Correct
*b
Incorrect
Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap assembly.
Note:Be sure to install the O-ring in the proper location, otherwise engine oil may leak.
Do not twist the O-ring.
Set a new oil filter element in the oil filter cap assembly.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and install the oil filter cap assembly.
Note:Make sure that the O-ring does not get caught between the parts.
-
*1
Oil Filter Cap Assembly
*2
O-ring
*a
Oil Filter Bracket
*b
Oil Filter Bracket Clip
*c
No Gap
Using SST, tighten the oil filter cap assembly.
09228-06501
25 N*m
255 kgf*cm
18 ft.*lbf
Note:After tightening the oil filter cap assembly, make sure that there is no gap and that the O-ring is not protruding.
Do not remove the oil filter bracket clip when installing the oil filter cap assembly.
Do not cross thread the oil filter cap assembly.
ADD ENGINE OIL
Add new engine oil and install the oil filler cap.
Table 1. Standard Oil Grade Oil Grade
Oil Viscosity (SAE)
ACEA C2
0W-30
5W-30
Table 2. Standard Capacity Item
Standard Condition
Drain and refill with oil filter change
3.7 liters (3.9 US qts, 3.3 Imp. qts)
Drain and refill without oil filter change
3.3 liters (3.5 US qts, 2.9 Imp. qts)
Dry fill
4.3 liters (4.5 US qts, 3.8 Imp. qts)
Table 3. Standard Capacity (for Destination Package for Turkey Sedan) Item
Standard Condition
Drain and refill with oil filter change
3.9 liters (4.1 US qts, 3.4 Imp. qts)
Drain and refill without oil filter change
3.5 liters (3.7 US qts, 3.1 Imp. qts)
Dry fill
4.5 liters (4.8 US qts, 4.0 Imp. qts)
INSPECT FOR OIL LEAK
Warm up the engine. Make sure that there are no engine oil leaks from the area that was worked on.
CHECK ENGINE OIL LEVEL
INSTALL OIL FILTER ELEMENT SERVICE HOLE COVER (for Full Cover Type)
-
Install the oil filter element service hole cover with the 8 clips.
-