CHECK WINDOW LOCK FUNCTION
Tech Tips
Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).
When the window lock switch of the multiplex network master switch assembly is pushed: Check that the front passenger and rear windows are disabled.
When the window lock switch is pushed in again: Check that the front passenger and rear windows can be operated normally.
CHECK MANUAL UP / DOWN FUNCTION
Check that the driver door power window operates as follows:
Condition | Master Switch | Switch Operation | Power Window |
---|---|---|---|
Engine switch on (IG) | Driver door | Pulled halfway up | UP (Closes) |
Pushed halfway down | DOWN (Opens) |
Check that the front passenger door window and rear power windows operate as follows:
Condition | Regulator Switch | Switch Operation | Power Window |
---|---|---|---|
|
Front passenger door | Pulled halfway up | UP (Closes) |
Pushed halfway down | DOWN (Opens) | ||
Rear LH door | Pulled halfway up | UP (Closes) | |
Pushed halfway down | DOWN (Opens) | ||
Rear RH door | Pulled halfway up | UP (Closes) | |
Pushed halfway down | DOWN (Opens) |
CHECK AUTO UP / DOWN FUNCTION
Check that the driver door power window operates as follows:
Condition | Master Switch | Switch Operation | Power Window |
---|---|---|---|
Engine switch on (IG) | Driver door | Pulled up (One touch operation) | AUTO UP (Closes) |
Pushed down (One touch operation) | AUTO DOWN (Opens) |
Check that the front passenger door window and rear power windows operate as follows:
Condition | Regulator Switch | Switch Operation | Power Window |
---|---|---|---|
|
Front passenger door | Pulled up (One touch operation) | AUTO UP (Closes) |
Pushed down (One touch operation) | AUTO DOWN (Opens) | ||
Rear LH door | Pulled up (One touch operation) | AUTO UP (Closes) | |
Pushed down (One touch operation) | AUTO DOWN (Opens) | ||
Rear RH door | Pulled up (One touch operation) | AUTO UP (Closes) | |
Pushed down (One touch operation) | AUTO DOWN (Opens) |
CHECK REMOTE MANUAL UP / DOWN FUNCTION
Check that the front passenger door window and rear power windows operate as follows:
Condition | Master Switch | Switch Operation | Power Window |
---|---|---|---|
|
Front passenger door | Pulled halfway up | UP (Closes) |
Pushed halfway down | DOWN (Opens) | ||
Rear LH door | Pulled halfway up | UP (Closes) | |
Pushed halfway down | DOWN (Opens) | ||
Rear RH door | Pulled halfway up | UP (Closes) | |
Pushed halfway down | DOWN (Opens) |
CHECK REMOTE AUTO UP / DOWN FUNCTION
Check that the front passenger door window and rear power windows operate as follows:
Condition | Master Switch | Switch Operation | Power Window |
---|---|---|---|
|
Front passenger door | Pulled up (One touch operation) | AUTO UP (Closes) |
Pushed down (One touch operation) | AUTO DOWN (Opens) | ||
Rear LH door | Pulled up (One touch operation) | AUTO UP (Closes) | |
Pushed down (One touch operation) | AUTO DOWN (Opens) | ||
Rear RH door | Pulled up (One touch operation) | AUTO UP (Closes) | |
Pushed down (One touch operation) | AUTO DOWN (Opens) |
CHECK KEY-OFF OPERATION FUNCTION
Check that each power window can be operated with the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly after the engine switch is turned off.
Tech Tips
If the window lock switch is on, the power windows cannot be operated by using the power window regulator switch assembly and rear power window regulator switch assembly. Therefore, turn the window lock switch off before checking the window operation.
Check that the key-off operation function does not operate immediately after the driver door or front passenger door is opened.
Tech Tips
Even if the driver door or front passenger door is opened during auto window operation while the key-off operation function is on, the window will stop operating.*1
Even if the driver door or passenger door is opened during automatic window operation while the key-off operation function is on, the window will continue operating.*2
*1: w/ Canister Pump Module
*2: w/o Canister Pump Module
Check that all the power windows cannot be operated after more than approximately 43 seconds have elapsed since the engine switch is turned off.
CHECK WIRELESS TRANSMITTER-LINKED FUNCTION (w/o Canister Pump Module)*
*: This function is set through the customize function, as it is off by default.
Check that all power windows operate as follows when operating the electrical key transmitter:
Condition | Transmitter Operation | Power Window |
---|---|---|
No key is inside vehicle, and all doors are closed and locked | LOCK switch pressed for more than 2.4 seconds | UP (Closes) |
No key is inside vehicle, and all doors are closed and locked | LOCK switch released | STOP |
No key is inside vehicle, and all doors are closed and locked | UNLOCK switch pressed for more than 2.4 seconds | DOWN (Opens) |
No key is inside vehicle, and all doors are closed and locked | UNLOCK switch released | STOP |
CHECK KEY-LINKED FUNCTION*
*: This function is set through the customize function, as it is off by default.
Check that all power windows operate as follows:
Condition | Door Key Cylinder Operation | Power Window |
---|---|---|
No key is inside vehicle, and all doors are closed | Key is turned to the lock position and held for more than 1.5 seconds | UP (Closes) |
No key is inside vehicle, and all doors are closed | Returned to neutral position | STOP |
No key is inside vehicle, and all doors are closed | Key is turned to the unlock position and held for more than 1.5 seconds | DOWN (Opens) |
No key is inside vehicle, and all doors are closed | Returned to neutral position | STOP |
CHECK WINDOW OPEN WARNING FUNCTION
Open a window by using the power window switch.
When the engine switch is turned from on (IG) to off and the driver door is opened with the key in the vehicle, check that the warning buzzer in the combination meter assembly sounds once. Then, check that the multi-information display on the combination meter assembly displays "Window opened".
CHECK JAM PROTECTION FUNCTION
Check the basic function.
CAUTION:
Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.
Tech Tips
The jam protection function is operative during both the auto up and manual up operations while the engine is running or the engine switch is on (IG), and also for approximately 43 seconds after the engine switch is turned off.
Fully open the window.
*a | Check Jig |
*b | Cloth |
Set a check jig wrapped with a piece of cloth near the window fully closed position.
Operate the auto up or manual up function to check that the power window stops and goes down after the check jig is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.) or approximately 5 seconds have elapsed.
Tech Tips
If the check jig is caught when the opening is approximately 75 mm (2.95 in.) or more, the power window goes down approximately 125 mm (4.93 in.) or approximately 2.5 seconds have elapsed.
While the power window is moving down, check that the door glass cannot be raised using the power window switch.
CHECK POWER WINDOW SWITCH LED ILLUMINATION
Check the LED illumination (multiplex network master switch assembly).
Check that the LEDs located in the multiplex network master switch assembly illuminate when the engine switch is turned on (IG).
Check the LED illumination (power window regulator switch assembly).
Check that the LED located in the power window regulator switch assembly illuminates when the engine switch is turned on (IG).
Check the LED illumination (rear power window regulator switch assembly).
Check that the LED located in each rear power window regulator switch assembly illuminates when the engine switch is turned on (IG).