FRONT CONSOLE BOX (for 5-Passenger with Ottoman) REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

    A01GLHB

    1. Pull the front part of the instrument panel finish panel end LH to detach the 6 clips.

    2. Pull the instrument panel finish panel end LH to detach 3 clips and remove the instrument panel finish panel end LH.

  2. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01GJB3

      Lower the shift lever boot and disconnect it from the shift lever knob sub-assembly.

    2. A01GKLB

      Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.

  4. REMOVE NO. 3 BOX PANEL

    A01GJKI

    1. Detach the 4 claws and remove the No. 3 box panel.

  5. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

    A01GKM5E01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Move the shift lever to N.

    3. Remove the 2 screws.

    4. Detach the 6 clips and remove the upper rear console panel sub-assembly.

    5. Disconnect each connector and each wire harness clamp.

  6. REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL


    1. Apply protective tape as shown in the illustration.

    2. Hold the opposite end with one hand as shown in the illustration so that the clip can be firmly pushed.

    3. Insert a screwdriver at the location shown in the illustration, and then push the lower clip on the backside of the upper instrument cluster finish panel towards the rear of the vehicle to detach it.

      Note

      At this time, all the clips may become detached and the upper instrument cluster finish panel may suddenly come off. Therefore, slowly push on the clip to detach it.

      Tech Tips


      • Tape the screwdriver tip before use.

      • The upper clip of the upper instrument cluster finish panel may become detached at the same time.

      A01GMGZE01
      Text in Illustration
      *1 Protective Tape *2 Lower Clip
      A01GKOV Rear of the Vehicle - -
    4. Insert a screwdriver at the location shown in the illustration, and then push the lower clip on the backside of the upper instrument cluster finish panel towards the rear of the vehicle to detach it.

      Note


      • Slowly push on the clip to detach it.

      • At this time, all the clips may become detached and the upper instrument cluster finish panel may suddenly come off. Therefore, place one hand on the upper instrument cluster finish panel as shown in the illustration.

      Tech Tips


      • Tape the screwdriver tip before use.

      • The upper clip of the upper instrument cluster finish panel may become detached at the same time.

      A01GIDWE01
      Text in Illustration
      *1 Protective Tape *2 Lower Clip
      A01GKOV Rear of the Vehicle - -
    5. A01GMAXE01
      Text in Illustration
      *1 Protective Tape
      A01GL9Y Upper Instrument Cluster Finish Panel Edge

      Insert moulding remover A between the upper instrument cluster finish panel and lower No. 1 instrument panel finish panel, and between the upper instrument cluster finish panel and lower No. 2 instrument panel finish panel to detach the 3 upper clips and remove the upper instrument cluster finish panel.

      Note

      If pressure is applied to the edge of the upper instrument cluster finish panel using moulding remover A, the surface may be damaged. Therefore, insert moulding remover A deep past the edge of the upper instrument cluster finish panel to detach the clips.

      Tech Tips

      If any of the upper clips have become detached during the previous procedure, detach the remaining clips to remove the upper instrument cluster finish panel.

  7. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Disconnect the connector.

    2. A01GL4H

      Detach the 6 clips and remove the upper console panel sub-assembly.

  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    A01GIBN

    1. Detach the 4 clips and 5 guides and remove the lower No. 1 instrument panel finish panel.

    2. Disconnect the connector.

  9. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

    A01GLFK

    1. Detach the 4 clips and 5 guides and remove the lower No. 2 instrument panel finish panel.

  10. REMOVE LOWER CONSOLE COVER


    1. Remove the lower console cover.

  11. REMOVE UPPER REAR CONSOLE PANEL GARNISH

    A01GIHSE02
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape as shown in the illustration.

    2. Using moulding remover B, detach the 5 clips and 3 guides, and then remove the upper rear console panel garnish.

  12. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH

    A01GJQW

    1. Remove the 2 screws and move the upper No. 1 console panel garnish in the direction of the arrow to remove it.

  13. REMOVE REAR CONSOLE BOX GARNISH

    A01GJSLE02
    Text in Illustration
    *1 Protective Tape

    1. Put protective tape as shown in the illustration.

    2. Using moulding remover A, detach the 2 clips and remove the rear console box garnish.

  14. REMOVE REAR NO. 1 CONSOLE END PANEL GARNISH

    A01GJUM

    1. Remove the 2 screws.

    2. Detach the 2 clips and 4 guides, and then remove the rear No. 1 console end panel garnish.

  15. REMOVE REAR NO. 2 CONSOLE END PANEL GARNISH

    Tech Tips

    Use the same procedure described for the rear No. 1 console end panel garnish.

  16. REMOVE CONSOLE COMPARTMENT BOX ASSEMBLY WITH TELEVISION DISPLAY


    1. Remove the 6 bolts.

    2. Move the console compartment box assembly with television display upward to detach the 2 hooks and disconnect the 3 connectors.

      A01GN41
    3. A01GNMS

      Move the console compartment box assembly with television display backward and disconnect the 3 connectors.

    4. A01GN3Y

      Move the console compartment box assembly with television display backward and disconnect the connector.

  17. REMOVE NO. 2 CONSOLE BOX DUCT

    A01GN73

    1. Remove the 2 clips and No. 2 console box duct.

  18. REMOVE CONSOLE BOX ASSEMBLY

    A01GHJP

    1. Disconnect the 4 connectors and detach the wire harness clamp.

    2. Remove the 2 screws and 4 bolts.

    3. Detach the 2 clips and remove the console box assembly.