UPPER INSTRUMENT PANEL INSTALLATION


  1. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY


    1. When using a new upper instrument panel sub-assembly:


      1. Immediately before installing the upper instrument panel assembly, twist and cut off the portions shown in the illustration.

        A01JAGO
    2. Engage the 5 claws as shown in the illustration.

    3. Engage the 2 claws and 4 clips, and install the upper instrument panel assembly as shown in the illustration.

      A01JBHIE01
    4. Install the 2 bolts <B>.

    5. Install the 2 passenger airbag bolts <A>.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      A01J97YE01
      Text in Illustration
      *1 Passenger Airbag Bolt <A> *2 Bolt <B>
    6. Engage the 2 clamps.

    7. Connect each connector.

      A01JATT
  2. CONNECT NO. 3 INSTRUMENT PANEL WIRE


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01JBAK

      Connect the connector.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 7 claws.

    3. Install the center instrument cluster finish panel garnish with the 2 screws <C>.

      A01JB9T
  4. INSTALL INSTRUMENT CLUSTER FINISH PANEL END


    1. A01JCPIE01

      Engage the 2 guides and 5 claws to install the instrument cluster finish panel end as shown in the illustration.

  5. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  6. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01JCVZE01

      Engage the 2 guides and 6 claws to install the No. 2 instrument panel speaker panel sub-assembly as shown in the illustration.

  7. INSTALL FRONT PILLAR GARNISH CORNER PIECE RH


    1. A01JAHO

      Engage the 3 claws to install the front pillar garnish corner piece RH.

  8. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  9. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY


    1. A01J9Y7

      Connect the connector.

    2. Install the front No. 2 speaker assembly with the 2 bolts.

  10. INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. A01J8F1E01

      Engage the 2 guides and 6 claws to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.

  11. INSTALL FRONT PILLAR GARNISH CORNER PIECE LH


    1. A01JAS2

      Engage the 3 claws to install the front pillar garnish corner piece LH.

  12. INSTALL FRONT PILLAR GARNISH LH


    1. A01JBCIE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Remove the protective cover.

    2. A01JD90E01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Make sure that the front pillar garnish clip is not damaged.

      Note


      • If there is any damage, replace the garnish clip with a new one.

      • When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

    3. Engage the claw to direction indicated by the arrow (1).

    4. Engage the 3 guides to direction indicated by the arrow (2).

    5. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

      Tech Tips

      Tape the needle-nosed pliers tip before use.

    6. A01J9PB

      Engage 2 clips to install the front pillar garnish LH.

  13. INSTALL INSTRUMENT PANEL FINISH PANEL END RH


    1. A01JCP4

      Engage the guide as shown in the illustration.

    2. A01JBC7

      Engage the guide as shown in the illustration.

    3. A01J98N

      Engage the 4 claws to install the instrument panel finish panel end RH.

  14. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01JC1FE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  15. INSTALL GLOVE COMPARTMENT DOOR


    1. Open the glove compartment door assembly.

    2. A01J9YD

      Insert the glove compartment door as shown in the illustration.

    3. Engage the 7 claws to install the glove compartment door.

  16. INSTALL NO. 2 INSTRUMENT PANEL REGISTER


    1. A01JA22

      Engage the 3 claws and clip to install the No. 2 instrument panel register.

  17. INSTALL NO. 1 SIDE DEFROSTER NOZZLE


    1. A01JAQW

      Engage the 3 claws to install the No. 1 side defroster nozzle.

  18. INSTALL INSTRUMENT PANEL FINISH PANEL END LH


    1. A01JCR3

      Engage the guide as shown in the illustration.

    2. A01JC93

      Engage the guide as shown in the illustration.

    3. A01JDAE

      Engage the 4 claws to install the instrument panel finish panel end LH.

  19. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01JDC6E01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  20. INSTALL NO. 1 CENTER INSTRUMENT CLUSTER FINISH PANEL


    1. A01J9TA

      Engage the 4 claws to install the No. 1 center instrument cluster finish panel.

  21. INSTALL NO. 1 INSTRUMENT PANEL REGISTER


    1. A01JC0M

      Engage the 4 claws to install the No. 1 instrument panel register.

  22. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Connect each connector.

    2. Engage the clamp.

    3. A01J9TK

      Engage the 2 guides and claw to connect the hood lock control cable.

    4. A01J9Q6

      Engage the 6 claws and clip.

    5. A01JA5Y

      Install the lower instrument panel finish panel assembly with the screw <C>.

  23. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01J99M

      Engage the 2 clips.

    2. Install the cowl side trim board LH with the clip.

  24. INSTALL FRONT DOOR SCUFF PLATE LH


    1. A01JB0N

      Engage the 10 claws to install the front door scuff plate LH.

  25. INSTALL NAVIGATION RECEIVER WITH BRACKET (w/ Navigation System)


    1. A01JAM5

      Engage the 4 claws to temporarily install the navigation receiver assembly with bracket as shown in the illustration.

    2. A01JCMN

      Install the navigation receiver assembly with bracket with the 4 bolts.

  26. INSTALL RADIO RECEIVER WITH BRACKET (w/o Navigation System)


    1. Connect each connector.

    2. A01J9D0

      Engage the 4 claws as shown in the illustration.

    3. A01JD1M

      Install the radio receiver with bracket with the 4 bolts.

  27. INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01JBMF

      Install the radio tuner opening cover with bracket with the 4 bolts <B>.

  28. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Radio Receiver)


    1. A01JADX

      Engage the 4 claws to install the center instrument cluster finish panel sub-assembly.

  29. INSTALL UPPER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY


    1. A01JD4M

      Connect the connector.

    2. Engage the 3 claws to install the upper instrument panel finish panel sub-assembly.

  30. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. Engage the 14 claws to install the instrument cluster finish panel garnish.

      A01J8FE
  31. INSTALL INSTRUMENT PANEL CUP HOLDER ASSEMBLY


    1. A01JAMI

      Install the instrument panel cup holder with the 4 screws <C> to the lower center instrument cluster finish panel sub-assembly.

  32. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01J96O

      Engage the 7 claws and 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  33. INSTALL INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01JCDA

      Connect each connector.

    2. Engage the 6 claws to install the integration control and panel assembly.

  34. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  35. INSTALL REAR NO. 3 FLOOR BOARD


    1. A01JC33

      Engage the 2 guides to install the rear No. 3 floor board.

  36. INSTALL REAR DECK FLOOR BOX


    1. Install the rear deck floor box.

  37. INSTALL REAR NO. 2 FLOOR BOARD


    1. A01JCWRE01

      Engage the 3 guides <A>.

    2. Engage the 2 guides <B> and install the rear No. 2 floor board as shown in the illustration.

  38. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.