PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.
REMOVE REAR NO. 3 FLOOR BOARD
Remove the rear No. 3 floor board.
REMOVE DECK FLOOR BOX RH
Fold back the rear No. 2 floor board.
Remove the deck floor box RH Click here.
REMOVE REAR NO. 3 FLOOR BOARD UPPER PLATE
Disengage the 2 claws and remove the rear No. 3 floor board upper plate.
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)
Disengage the 3 claws and guide.
Disconnect each connector and remove the No. 2 instrument panel under cover sub-assembly.
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)
for LHD:
*1 | Glove Compartment Door Stopper Sub-assembly |
*2 | Moulding Remover |
*3 | Lower Instrument Panel Sub-assembly |
*4 | Glove Compartment Door Assembly |
*5 | Stopper |
Disengage the claw and release the glove compartment door stopper sub-assembly.
Insert the moulding remover into the location shown in the illustration.
Move the moulding remover in the direction indicated by the arrow to bend the lower instrument panel sub-assembly and release the stopper (A).
Tech Tips
Use the same procedure to release the stopper (B).
for RHD:
*1 | Glove Compartment Door Stopper Sub-assembly |
*2 | Stopper |
Disengage the claw and release the glove compartment door stopper sub-assembly.
Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.
*a | Close |
*b | Open Approximately |
Open the glove compartment door assembly to approximately 55° from its closed position. Pull it horizontally in the direction indicated by the arrow to disengage the 2 hinges and remove the glove compartment door assembly.
Note
Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.
REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)
Tech Tips
Use the same procedure described for the LH side Click here.
REMOVE COWL SIDE TRIM BOARD RH (for RHD)
Tech Tips
Use the same procedure described for the LH side Click here.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for RHD)
Remove the screw <C>.
Disengage the 6 claws and clip as shown in the illustration.
Disengage the claw and 2 guides and disconnect the hood lock control cable.
Disconnect each connector and clamp, and remove the lower instrument panel finish panel assembly.
REMOVE ECU INTEGRATION BOX RH
for LHD:
Disconnect each connector.
Disengage the 3 clamps and disconnect the wire harness.
Remove the bolt, 2 nuts and ECU integration box RH.
for RHD:
Disconnect each connector.
Disengage the clamp and disconnect the wire harness.
Remove the bolt, nut and ECU integration box RH.
REMOVE PARKING ASSIST ECU
for LHD:
Disengage the claw and remove the parking assist ECU.
Tech Tips
When removing the parking assist ECU, if the bracket for the driving support ECU assembly is on top of the bracket for the parking assist ECU, remove the driving support ECU assembly first Click here.
for RHD:
Disengage the claw and remove the parking assist ECU.
Tech Tips
When removing the parking assist ECU, if the bracket for the driving support ECU assembly is on top of the bracket for the parking assist ECU, remove the driving support ECU assembly first Click here.