COMBINATION METER REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)


    1. Disable the auto away/return function by changing the customize parameter Click here.

      Note

      Record the current customize parameter setting (whether the auto away/return function is enabled or disabled) in order to restore the current setting after finishing this operation.

      Tech Tips

      Performing the above operation disables the auto away/return function when the ignition switch is turned off.

    2. Turn the ignition switch to ON. Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.

    3. Turn the ignition switch off and disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for TMMK Made)


    1. B000KDO

      Disconnect the front door opening trim weatherstrip LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP (for TMC, TMMR Made)


    1. B000HXQ

      Disconnect the front door opening trim weatherstrip LH.

  6. REMOVE INSTRUMENT SIDE PANEL LH (for TMMK Made)


    1. B000H81

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000IQ4

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  7. REMOVE INSTRUMENT SIDE PANEL (for TMC, TMMR Made)


    1. B000HH8

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000MY7

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  8. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for TMMK Made)


    1. B000HO0

      Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.

  9. REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. B000H9B

      Disengage the 2 claws and 4 clips to remove the upper instrument panel finish panel as shown in the illustration.

    2. w/ Smart Entry and Start System:


      1. Disconnect the connector.

  10. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for TMMK Made)


    1. B000M8R

      Apply protective tape to the area shown in the illustration.

      Text in Illustration
      B000JL5 Protective Tape
    2. B000HAB

      Disengage the 2 clips as shown in the illustration.

    3. B000HMM

      Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.

  11. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY (for TMC, TMMR Made)


    1. B000J4N

      Disengage the 4 clips to remove the No. 1 instrument panel register assembly as shown in the illustration.

  12. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for TMMK Made)


    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. B000L6J

      Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.

    3. B000NP0

      Disengage the 5 claws, 5 clips and 2 guides.

    4. Disconnect each connector.

    5. B000I7Y

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  13. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for TMC, TMMR Made)


    1. for Manual Tilt and Manual Telescopic Steering Column:


      1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. B000MKZ

      Using a moulding remover, disengage the 4 clips and 2 guides.

    3. for LHD:


      1. B000HY1

        Disengage the 3 claws, 7 clips and 4 guides.

    4. for RHD:


      1. B000HJQ

        Disengage the 4 claws, 5 clips and 4 guides as shown in the illustration.

    5. Disconnect each connector.

    6. B000KKH

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  14. REMOVE COMBINATION METER ASSEMBLY


    1. B000I9P

      Remove the 4 screws.

    2. B000LWI

      Disengage the wire harness clamp.

    3. Disconnect the 2 connectors to remove the combination meter assembly.