DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / (desired system) / Data List.
According to the display on the tester, read the Data List.
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
Door Lock Status | Back door lock status signal / Lock or Unlock | Lock: Back door locked Unlock: Back door unlocked |
- |
Half Latch SW | Half-latch switch signal / ON or OFF | ON: Half-latch switch on OFF: Half-latch switch off |
- |
Closer Position SW | Closer position switch signal / ON or OFF | ON: Closer position switch on OFF: Closer position switch off |
- |
Courtesy SW | Back door courtesy switch signal / ON or OFF | ON: Back door courtesy switch on OFF: Back door courtesy switch off |
- |
RH CTSY SW of Tail Gate Panel | Lower tail gate courtesy switch RH signal / ON or OFF | ON: Tail gate closed OFF: Tail gate open |
- |
LH CTSY SW of Tail Gate Panel | Lower tail gate courtesy switch LH signal / ON or OFF | ON: Tail gate closed OFF: Tail gate open |
- |
PBD Touch Sensor (Right) | Power back door sensor RH signal / ON, OFF or Open | ON: Power back door sensor RH pressed OFF: Power back door sensor RH not pressed Open: Power back door sensor RH circuit open |
- |
PBD Touch Sensor (Left) | Power back door sensor LH signal / ON, OFF or Open | ON: Power back door sensor LH pressed OFF: Power back door sensor LH not pressed Open: Power back door sensor LH circuit open |
- |
PBD Main SW | Power back door main switch signal / ON or OFF | ON: Power back door main switch not pressed OFF: Power back door main switch pressed |
- |
PBD Close SW | Back door control switch signal / ON or OFF | ON: Back door control switch on OFF: Back door control switch off |
- |
IG SW | Engine switch signal / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off |
- |
PBD Position (Close-1/4) | Back door position (Full close - 1/4 open) / Caution or OK | Caution: Back door position is not fully closed to 1/4 opened OK: Back door position is fully closed to 1/4 opened |
- |
PBD Position (1/4-2/4) | Back door position (1/4 open - 2/4 open) / Caution or OK | Caution: Back door position is not 1/4 opened to 2/4 opened OK: Back door position is 1/4 opened to 2/4 opened |
- |
PBD Position (2/4-3/4) | Back door position (2/4 open - 3/4 open) / Caution or OK | Caution: Back door position is not 2/4 opened to 3/4 opened OK: Back door position is 2/4 opened to 3/4 opened |
- |
PBD Position (3/4-Open) | Back door position (3/4 open - Full open) / Caution or OK | Caution: Back door position is not 3/4 opened to fully opened OK: Back door position is 3/4 opened to fully opened |
- |
PBD SW Operation | Power back door switch operation condition signal / 0.0s or 0.8s | Current customize setting displayed | - |
PBD Buzz In Use | Power back door warning buzzer operation condition signal / ON or OFF | Current customize setting displayed | - |
Wireless PBD SW Operation | Transmitter switch operation condition signal / 1 time, 2 times, 0.8 sPR, OFF | Current customize setting displayed | - |
# Codes | Number of stored trouble codes / min.: 0, max.: 255 | Number of DTCs will be displayed | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
Back Door Open SW | Door control switch signal / ON or OFF | ON: Door control switch on OFF: Door control switch off |
- |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Back Door / Active Test.
According to the display on the tester, perform the Active Test.
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Latch Releaser | Operate back door lock | ON / OFF | - |
PBD Motor | Operate power back door motor | Forward / OFF Reverse / OFF |
- |
PBD Clutch | Operate power back door clutch | ON / OFF | - |
PBD Buzzer | Operate warning buzzer | ON / OFF | - |
Courtesy SW Signal | Operate back door courtesy light switch signal | ON / OFF | - |
PBD Close SW Light | Operate PBD close switch Light | ON / OFF | - |