РЕЛЕ ПРОВЕРКА БЕЗ СНЯТИЯ С АВТОМОБИЛЯ


  1. INSPECT AIR PUMP HEATER RELAY (AI-PMP HTR)


    1. A01ER14E02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage is applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  2. INSPECT AIR INJECTION VSV RELAY (AI-VSV)


    1. A01ER14E02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage is applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  3. INSPECT NO. 1 INTEGRATION RELAY (IG2)


    1. Measure the resistance of the IG2 MAIN fuse.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        IG2 MAIN fuse Always Below 1 Ω

        If the result is not as specified, replace the IG2 MAIN fuse.

    2. Measure the resistance of the ignition relay No. 2 (IG2) circuit.


      1. A01ENV6E24
        Text in Illustration
        *a

        Component without harness connected

        (No. 1 Integration Relay)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-6 and 1B-7 10 kΩ or higher
        Battery voltage is applied to terminals 1B-6 and 1B-7 Below 1 Ω

        If the result is not as specified, replace the No. 1 integration relay.

  4. INSPECT NO. 1 INTEGRATION RELAY (EFI)


    1. Measure the resistance of the EFI MAIN fuse.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        EFI MAIN fuse Always Below 1 Ω

        If the result is not as specified, replace the EFI MAIN fuse.

    2. Measure the resistance of the EFI relay circuit.


      1. A01ENV6E24
        Text in Illustration
        *a

        Component without harness connected

        (No. 1 Integration Relay)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
        Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω

        If the result is not as specified, replace the No. 1 integration relay.

  5. INSPECT EFI NO. 2 RELAY


    1. A01ER14E01

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage is applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  6. INSPECT NO. 1 INTEGRATION RELAY (A/F)


    1. Measure the resistance of the A/F fuse.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        A/F fuse Always Below 1 Ω

        If the result is not as specified, replace the A/F fuse.

    2. Measure the resistance of the A/F sensor heater relay circuit.


      1. A01ENV6E24
        Text in Illustration
        *a

        Component without harness connected

        (No. 1 Integration Relay)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        1C-1 - 1A-4 Battery voltage is not applied to terminals 1A-2 and 1A-3 10 kΩ or higher
        Battery voltage is applied to terminals 1 A-2 and 1A-3 Below 1 Ω

        If the result is not as specified, replace the No. 1 integration relay.

  7. INSPECT MAIN BODY ECU (IG1 NO. 1)

    A01ESI0E03

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      2A-1 - 2B-17 Battery voltage is not applied to terminals 2B-5 and 2D-43 10 kΩ or higher
      Battery voltage is applied to terminals 2B-5 and 2D-43 Below 1 Ω
      Text in Illustration
      *a

      Component without harness connected

      (Main Body ECU)

      If the result is not as specified, replace the cowl side junction block LH.

  8. INSPECT STARTER RELAY (ST)


    1. A01EMVTE02

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  9. INSPECT STARTER CUT RELAY (ST CUT)


    1. A01ENSNE26

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied to terminals 1 and 2 10 kΩ or higher
      Battery voltage applied to terminals 1 and 2 Below 1 Ω

      If the result is not as specified, replace the relay.

  10. INSPECT MAIN BODY ECU (ACC RELAY)

    A01EO5FE02
    Text in Illustration
    *a

    Component without harness connected

    (Main Body ECU)

    - -

    1. Measure the resistance of the ACC relay circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2A-1 - 2D-8 Battery voltage not applied between 2D-45 and 2D-62 10 kΩ or higher
        Battery voltage applied between 2D-45 and 2D-62 Below 1 Ω

        If the result is not as specified, replace the main body ECU.