REAR SEAT ASSEMBLY (for LH Side) INSTALLATION


  1. INSTALL REAR SEAT ASSEMBLY LH


    1. A01NEZD

      Temporarily install the 2 bolts on the front side of the seat.

    2. A01NGWM

      Temporarily install the 3 bolts on the rear side of the seat.

    3. A01NDMI

      Connect the connector.

    4. Install the rear seat assembly LH with the 5 bolts.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }
  2. CONNECT REAR SEAT LOCK CABLE ASSEMBLY LH


    1. When replacing the rear seat assembly LH or No. 2 rear seat reclining control cable with a new one:


      1. A01NHBE

        Connect the rear seat assembly LH or No. 2 rear seat reclining control cable as shown in the illustration.

    2. When replacing the rear seat lock cable assembly LH with a new one:


      1. Engage the joint piece with the cable of the rear seat lock cable assembly LH.

      2. Connect the rear seat lock cable assembly LH and connector case as shown in the illustration.

        A01NG0T
      3. Push the lock pin of the connector case as shown in the illustration to connect the rear seat lock cable assembly LH.

        A01NGE5
    3. When reusing the rear seat assembly LH, No. 2 rear seat reclining control cable and rear seat lock cable assembly LH:


      1. Connect the rear seat lock cable assembly LH as shown in the illustration.

        A01NE90
      2. Connect the No. 2 rear seat reclining control cable as shown in the illustration.

        A01NCTKE01
        Text in Illustration
        *1 Seat Track Adjusting Handle *2 Protective Tape
      3. A01ND1A

        Install the rear seat reclining control cable to the cover as shown in the illustration.

      4. A01NGBT

        Connect the No. 2 rear seat reclining control cable as shown in the illustration.

    4. Return the seatback to the upright position.

    5. Press the adjusters lock piece to lock it as shown in the illustration.

      A01NH8QE01
      Text in Illustration
      *1 Adjusters Spring *2 Lock Piece

      Note

      When pressing the lock piece, make sure the adjusters spring is not compressed.

    6. A01NDJG

      Engage the guide.

    7. Connect the No. 2 fold seat stopper band assembly with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }
    8. A01NDU1

      Connect the rear seatback board carpet assembly with the 4 clips.

  3. INSPECT REAR SEAT SLIDE ADJUSTER LOCK


    1. Check that the left and right adjusters lock simultaneously when sliding the seat.

    2. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.

  4. INSTALL REAR SEAT INNER TRACK BRACKET COVER LH


    1. A01NFLC

      Engage the 4 claws and install the rear seat inner track bracket cover LH.

  5. INSTALL REAR SEAT OUTER TRACK BRACKET COVER LH


    1. A01NHXN

      Engage the 4 claws and install the rear seat outer track bracket cover LH.

  6. INSTALL REAR SEAT HEADREST ASSEMBLY LH


    1. A01NGP5

      Install the rear seat headrest assembly as shown in the illustration.

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. INSPECT SRS WARNING LIGHT

    Click here

  9. INSTALL REAR DECK FLOOR BOX


    1. A01NDSY

      Install the rear deck floor box with the 3 clips.