ROOF HEADLINING INSTALLATION


  1. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01NMXGE01
      Text in Illustration
      *1 Alignment mark (Brown)

      Align the alignment mark (Brown) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  2. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01NKBNE01
      Text in Illustration
      *1 Alignment mark (Pink)

      Align the alignment mark (Pink) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  3. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01NKMUE01
      Text in Illustration
      *1 Alignment mark (Light Blue)

      Align the alignment mark (Light Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  4. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01NMFJE01
      Text in Illustration
      *1 Alignment mark (Green)

      Align the alignment mark (Green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  5. INSTALL ROOF HEADLINING ASSEMBLY (for Standard Roof)


    1. A01NL4S

      Pull the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Engage the 2 fasteners.

      A01NMEI
    3. Engage the 12 claws and 3 clips.

    4. Connect the No. 4 antenna cord sub-assembly connector and engage the 2 claws and clamp to the rear pillar LH.

    5. Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 2 claws to the front pillar RH.

    6. Connect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors, and engage the 2 claws to the front pillar LH.

      A01NKSI

      Note

      After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

    7. A01NJGB

      Connect the No. 1 roof wire connector to the inner rear view mirror.

    8. w/ Rain Sensor:


      1. A01NI61

        Connect the No. 1 roof wire connector to the rain sensor.

    9. A01NLYS

      Connect the No. 2 antenna cord sub-assembly connectors and washer hose, and engage the 2 claws and 3 clamps to the rear pillar RH.

  6. INSTALL ROOF HEADLINING ASSEMBLY (for Sliding roof)


    1. A01NJQK

      Pull the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    2. Engage the 8 fasteners.

      A01NKMO
    3. Engage the 12 claws and 3 clips.

    4. Connect the No. 4 antenna cord sub-assembly connector and engage the 2 claws and clamp to the rear pillar LH.

    5. Connect the No. 1 roof wire connector to the sliding roof drive gear assembly.

    6. Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 2 claws to the front pillar RH.

    7. Connect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors, and engage the 2 claws to the front pillar LH.

      A01NJEX

      Note

      After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

    8. A01NJGB

      Connect the No. 1 roof wire connector to the inner rear view mirror.

    9. w/ Rain Sensor:


      1. A01NI61

        Connect the No. 1 roof wire connector to the rain sensor.

    10. A01NLYS

      Connect the No. 2 antenna cord sub-assembly connectors and washer hose, and engage the 2 claws and 3 clamps to the rear pillar RH.

  7. INSTALL ROOF HEADLINING ASSEMBLY (for Glass Roof)


    1. A01NN8L

      Open the sunshade trim sub-assembly as shown in the illustration.

      Note

      If the sunshade trim sub-assembly is closed, the roof headlining cannot be installed.

    2. A01NMWT

      Pull the roof headlining assembly into the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

    3. Engage the 12 fasteners.

      A01NM3L
    4. Engage the 12 claws and 3 clips.

    5. Connect the No. 4 antenna cord sub-assembly connector and engage the 2 claws and clamp to the rear pillar LH.

    6. Connect the No. 1 roof wire connector to the sliding roof drive gear assembly.

    7. Connect the No. 2 antenna cord sub-assembly connector and washer hose, and engage the 2 claws to the front pillar RH.

    8. Connect the No. 4 antenna cord sub-assembly connector and No. 1 roof wire connectors, and engage the 2 claws to the front pillar LH.

      A01NM6P

      Note

      After installation, make sure that the back door weatherstrip does not interfere with the roof headlining assembly.

    9. A01NJGB

      Connect the No. 1 roof wire connector to the inner rear view mirror.

    10. w/ Rain Sensor:


      1. A01NI61

        Connect the No. 1 roof wire connector to the rain sensor.

    11. A01NLYS

      Connect the No. 2 antenna cord sub-assembly connectors and washer hose, and engage the 2 claws and 3 clamps to the rear pillar RH.

  8. INSTALL VISOR HOLDER (for LH Side)


    1. A01NN81

      Engage the 2 claws.

    2. Push in the visor holder as shown in the illustration.

  9. INSTALL VISOR HOLDER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  10. INSTALL VISOR ASSEMBLY LH


    1. A01NI68

      Install the visor assembly LH with the 2 screws.

  11. INSTALL VISOR BRACKET COVER (for LH Side)


    1. A01NLJH

      Engage the 4 claws and install the visor bracket cover.

  12. INSTALL VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  13. INSTALL VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  14. INSTALL ASSIST GRIP SUB-ASSEMBLY


    1. A01NM5D

      Put an assist grip sub-assembly together as shown in the illustration.

    2. Install the assist grip sub-assembly.

      Tech Tips

      Use the same procedure for the other 3 assist grips.

  15. INSTALL COAT HOOK


    1. A01NMHI

      Install the coat hook with the screw.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  16. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01NMX3

      Engage the 2 claws to install the rain sensor cover.

  17. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. w/o Rear View Monitor System:


      1. Engage the 6 claws and install the inner rear view mirror stay holder cover.

      2. A01NLUR

        Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.

    2. w/ Rear View Monitor System:


      1. Engage the 2 claws and install the inner rear view mirror stay holder cover.

      2. A01NIIT

        Engage the 2 claws and install the inner rear view mirror stay holder cover as shown in the illustration.

  18. INSTALL SPOT LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01NKCRE01

      Insert the 2 guides.

    3. Engage the 2 clips to install the spot light assembly as shown in the illustration.

  19. INSTALL MAP LIGHT ASSEMBLY


    1. Connect each connector.

    2. A01NKMA

      Engage the 2 guides and 2 clips.

    3. Install the map light assembly with the 2 screws.

    4. A01NMN3

      Engage the 2 claws and connect the 2 caps.

    5. w/ Holder:


      1. Close the holder.

    6. w/o Holder:


      1. A01NIP3

        Engage the 2 claws to connect the cover.

  20. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH


    1. Pass the floor anchor of the rear seat outer seat belt assembly LH through the roof side inner garnish assembly LH.

    2. Engage the claw and 8 clips to install the roof side inner garnish assembly LH.

      A01NIKV
  21. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH


    1. A01NICRE01
      Text in Illustration
      *1 Protruding Part

      Connect the floor anchor end of the rear seat belt assembly and install the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the rear seat outer belt assembly to overlap the protruding part of the floor panel.

  22. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH


    1. Connect each connector.

    2. Engage the 2 clips and the 5 claws.

    3. Install the deck trim side panel assembly LH with the 2 bolts and 4 clips.

      A01NLMP
  23. INSTALL RECLINING REMOTE CONTROL BEZEL LH


    1. A01NLC2

      Engage the 4 claws and install the reclining remote control bezel LH.

  24. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)


    1. A01NJN3

      Install the No. 1 luggage compartment trim hook as shown in the illustration.

  25. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    1. A01NJ4O

      Install the 2 rope hook assemblies with the 2 bolts.

    2. Engage the 2 claws.

  26. INSTALL REAR SEAT SIDE COVER LH


    1. A01NJHB

      Engage the 2 claws and 3 clips.

    2. Install the rear seat side cover LH with the 2 clips.

  27. INSTALL REAR SEAT ASSEMBLY LH

    Click here

  28. INSTALL REAR FLOOR FINISH SIDE PLATE LH


    1. A01NLJE

      Engage the guide.

    2. Engage the claw and 2 clips.

    3. Install the rear floor finish side plate LH with the clip.

  29. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  30. CONNECT REAR SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  31. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH


    1. Connect the connector.

    2. Engage the 2 clips and the 5 claws.

    3. Install the deck trim side panel assembly RH with the 2 bolts and 5 clips.

      A01NL5Y
  32. INSTALL HEIGHT CONTROL SWITCH (w/ Air Suspension)


    1. Connect the connector.

    2. A01NM1V

      Engage the 2 claws to install the height control switch to the deck trim side panel assembly RH.

  33. INSTALL RECLINING REMOTE CONTROL BEZEL RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  34. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)


    1. A01NL62

      Install the No. 1 luggage compartment trim hook as shown in the illustration.

  35. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  36. INSTALL REAR SEAT SIDE COVER RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  37. INSTALL REAR SEAT ASSEMBLY RH

    Click here

  38. INSTALL REAR FLOOR FINISH SIDE PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  39. INSTALL REAR FLOOR FINISH PLATE


    1. A01NMPW

      Engage the 6 clips, 2 claws and 2 guides, and install the rear floor finish plate.

  40. INSTALL FRONT DECK FLOOR BOX


    1. A01NN39

      Install the front deck floor box with the clip.

  41. INSTALL DECK SIDE TRIM BOX LH (for Compact Spare Tire)


    1. A01NNFE

      Install the deck side trim box LH with the 2 clips.

  42. INSTALL DECK SIDE TRIM BOX LH (for Full Size Spare Tire)


    1. A01NKYS

      Install the deck side trim box LH with the 3 clips.

  43. INSTALL DECK SIDE TRIM BOX RH (for Compact Spare Tire)


    1. A01NN0A

      Install the deck side trim box RH with the 2 clips.

  44. INSTALL DECK SIDE TRIM BOX RH (for Full Size Spare Tire)


    1. A01NM4K

      Install the deck side trim box RH with the 3 clips.

  45. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Install the tonneau cover assembly.

  46. INSTALL NO. 3 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A01NIEE

      Engage the 2 guides and install the No. 3 rear floor board.

  47. INSTALL NO. 3 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A01NJCJ

      Engage the 2 guides and install the No. 3 rear floor board.

  48. INSTALL NO. 4 REAR FLOOR BOARD (for Compact Spare Tire)


    1. A01NLSZ

      Engage the 2 guides and install the No. 4 rear floor board.

  49. INSTALL NO. 4 REAR FLOOR BOARD (for Full Size Spare Tire)


    1. A01NMV0

      Engage the 2 guides and install the No. 4 rear floor board.

  50. INSTALL SPARE WHEEL COVER ASSEMBLY (for Compact Spare Tire)


    1. Install the spare wheel cover assembly.

  51. INSTALL DECK BOARD SUB-ASSEMBLY


    1. for Compact Spare Tire:


      1. A01NM7R

        Install the deck board sub-assembly with the 2 bolts.

    2. for Full Size Spare Tire:


      1. A01NM92

        Install the deck board sub-assembly with the 2 bolts.

    3. A01NIMA

      Engage the 3 fasteners as shown in the illustration.

  52. INSTALL CENTER PILLAR GARNISH LH


    1. Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar garnish LH.

    2. A01NJWZ

      Engage the clip to install the center pillar garnish LH with the 2 screws.

  53. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01NIAG

      Install the floor end of the front seat outer belt assembly with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    2. Check if the ELR locks.

      Note

      The check should be performed with the outer belt assembly installed.


      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.

  54. INSTALL LOWER CENTER PILLAR GARNISH LH


    1. A01NJUV

      Engage the 2 claws and the 5 clips to install the lower center pillar garnish LH.

  55. INSTALL REAR DOOR SCUFF PLATE LH


    1. A01NIFR

      Engage the 3 clips, guide and 6 claws, and install the rear door scuff plate LH.

  56. INSTALL FRONT PILLAR GARNISH LH


    1. A01NIVUE01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Remove the protective cover.

    2. A01NILVE01

      Make sure that the front pillar garnish clip is not damaged.

      Note


      • If there is any damage, replace the garnish clip with a new one.

      • When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

    3. Engage the 2 guides.

    4. Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

      Tech Tips

      Tape the tips of the needle-nosed pliers before use.

    5. Engage the 2 clips to install the front pillar garnish LH.

  57. INSTALL INSTRUMENT SIDE PANEL LH


    1. A01NJA8

      Engage the guide.

    2. Engage the 2 clips.

    3. Engage the claw to install the instrument side panel LH.

  58. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01NK5N

      Engage the 2 clips to install the cowl side trim sub-assembly LH.

    2. Install the clip.

  59. INSTALL FRONT DOOR SCUFF PLATE LH


    1. w/ Illumination:


      1. Connect the connector.

    2. A01NJ04

      Engage the 4 clips, guide and 7 claws, and install the front door scuff plate LH.

  60. INSTALL CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  61. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  62. INSTALL LOWER CENTER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  63. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  64. INSTALL FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  65. INSTALL INSTRUMENT SIDE PANEL RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  66. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  67. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and the LH side.

  68. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  69. INSTALL REAR DECK FLOOR BOX


    1. A01NIBL

      Install the rear deck floor box with the 3 clips.

  70. INSPECT SRS WARNING LIGHT

    Click here

  71. INSPECT SUSPENSION CONTROL SYSTEM (w/ Air Suspension)


    1. Inspect the suspension control system Click here.