DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected. Click here
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
Note
Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)
Apply protective tape to the areas shown in the illustration.
Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.
Note
Do not pull on the small storage compartment lid. Doing so may cause damage.
Disconnect each connector and remove the center instrument cluster finish panel assembly.
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 8 claws and guide, and remove the front door scuff plate LH.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Remove the clip.
Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)
Remove the 2 bolts <B>.
Disengage the 3 claws and 10 clips.
Disconnect each connector.
Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)
Remove the 2 bolts <B>.
Disengage the 3 claws and 10 clips.
Disconnect each connector and the aspirator duct.
Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.
REMOVE FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure for the RH side and the LH side.
REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Tech Tips
Use the same procedure for the RH side and the LH side.
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Disengage the 3 claws.
Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.
REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the 2 bolts <B> and 3 screws <F>.
Disengage the 4 claws and 3 clips.
Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.
REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
Disengage the 4 claws and 4 clips.
Disconnect the connector and remove the upper console panel sub-assembly.
REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)
Remove the No. 2 console box duct as shown in the illustration.
REMOVE LOWER REAR CONSOLE BOX
Remove the lower rear console box.
REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)
Remove the 4 bolts and 2 screws.
Disengage the 6 claws and remove the console box assembly.
REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)
Remove the 4 bolts and 2 screws.
Disconnect the connector.
Disengage the 6 claws, and remove the console box assembly.
REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)
Using a clip remover, remove the 2 clips.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for RHD)
Using a clip remover, remove the clip.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.
REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)
Using a clip remover, remove the clip.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)
Using a clip remover, remove the clip.
Remove the 3 screws <F>.
Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.
REMOVE YAW RATE AND ACCELERATION SENSOR
Disconnect the connector from the yaw rate and acceleration sensor.
Remove the 2 bolts and yaw rate and acceleration sensor.
Note
Do not remove the installation nuts.