CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
Tech Tips
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart Click here.
INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH
Install the rear seat reclining adjuster assembly LH with the 4 nuts.
Note
Be careful not to damage the vehicle body.
INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH
Tech Tips
Use the same procedures described for the LH side.
INSTALL REAR NO. 2 SEAT ADJUSTER ASSEMBLY
Connect the air duct to the vehicle body.
Install the rear No. 2 seat adjuster assembly with the 4 bolts and nut.
Note
Be careful not to damage the vehicle body.
*1 | Protruding Part |
Connect the anchor part of the rear center seat outer belt with the nut.
Note
Do not allow the anchor part of the rear center seat outer belt to overlap the protruding part of the anchor bracket.
INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY
Connect the air duct to the vehicle body.
Install the rear No. 1 seat adjuster assembly with the 4 bolts and nut.
Note
Be careful not to damage the vehicle body.
INSTALL REAR SEAT CENTER ARMREST ASSEMBLY
Connect the 2 connectors.
Install the rear seat center armrest assembly with the 2 bolts and nut.
Note
Be careful not to damage the vehicle body.
Attach the hook to the center seatback frame wire.
Attach the 2 clips to install the rear seat armrest hole board.
While pressing the button, lower the rear center seat headrest assembly.
Raise the rear seat center armrest assembly.
INSTALL REAR SEATBACK ASSEMBLY LH
Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.
Note
Be careful not to damage the vehicle body.
Install the 2 nuts.
Install the clip and attach the 3 pieces of fastening tape.
*1 | Fastening Tape |
Connect the 3 connectors and attach the 7 wire harness clamps.
Connect the 2 connectors.
Install the junction block with the bolt.
Connect the seat belt to the shoulder belt guide.
Attach the 2 claws to close the 2 caps.
*1 | Protruding Part |
Connect the anchor part of the rear seat 3 point type belt assembly with the bolt.
Note
Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.
INSTALL REAR SEATBACK ASSEMBLY RH
Tech Tips
Use the same procedures described for the LH side.
INSTALL REAR CENTER SEAT CUSHION ASSEMBLY
Attach the rear hook of the center seat cushion assembly to the center seatback frame sub-assembly.
Note
Be careful not to damage the vehicle body.
Attach the front hook of the rear center seat cushion assembly to the vehicle body.
INSTALL REAR SEAT CUSHION ASSEMBLY LH
Connect the connector.
Attach the rear hook of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.
Note
Be careful not to damage the vehicle body.
Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.
INSTALL REAR SEAT CUSHION ASSEMBLY RH
Tech Tips
Use the same procedures described for the LH side.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSTALL COWL TOP VENTILATOR LOUVER RH
Install the 6 clips and cowl top ventilator louver RH.
Note
If the cowl top ventilator louver RH is not properly installed, water may leak into the engine room and cause malfunctions. Therefore, make sure the cowl top ventilator louver RH is installed properly.
CHECK SRS WARNING LIGHT
CHECK REAR SEAT ASSEMBLY
Check the power seat operation:
Check the climate control seat system:
Check the seat vibration system:
CHECK REAR SUNSHADE SYSTEM
CHECK REAR DOOR SUNSHADE SYSTEM