Tech Tips
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.
REMOVE REAR NO. 3 FLOOR BOARD
Remove the rear No. 3 floor board.
REMOVE DECK FLOOR BOX RH
Fold back the rear No. 2 floor board.
Remove the deck floor box RH Click here.
REMOVE REAR NO. 3 FLOOR BOARD UPPER PLATE
Disengage the 2 claws and remove the rear No. 3 floor board upper plate.
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug.
REMOVE DOOR ASSIST GRIP COVER
Using a moulding remover, disengage the 6 claws, 2 clips and 3 guides, and remove the door assist grip cover.
REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Disengage the 7 claws and 2 guides.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
REMOVE REAR DOOR ARMREST COVER
Remove the rear door armrest cover.
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
*1 | Protective Tape |
Put protective tape around the rear door panel.
Remove the 2 screws.
Using a clip remover, disengage the 8 clips.
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Raise the rear door trim board sub-assembly and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.
for 8 Speakers:
Disconnect the connector.
REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly, and remove the rear door inside handle sub-assembly.
REMOVE REAR DOOR TRIM BRACKET
Remove the 2 screws and rear door trim bracket.
REMOVE REAR DOOR SERVICE HOLE COVER
Disconnect the 2 connectors.
Disengage the clamp.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through the rear door service hole cover.
Remove the rear door service hole cover.
Tech Tips
Remove any remaining butyl tape from the door.
REMOVE REAR DOOR GLASS RUN
Remove the rear door glass run.
REMOVE REAR DOOR WINDOW GUIDE SUB-ASSEMBLY
Remove the screw.
Remove the bolt and rear door window guide sub-assembly.
REMOVE REAR DOOR REAR GUIDE SEAL
*1 | Temporary Screw |
Loosen the temporary screw.
Remove the 2 screws and rear door rear guide seal.
Remove the temporary screw from the rear door rear guide seal.
REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Connect the cable to the negative (-) auxiliary battery terminal and rear power window regulator switch assembly.
Connect the rear power window regulator motor connector.
Move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the rear power window regulator switch assembly and rear power window regulator motor connector.
Remove the 2 bolts and rear door glass sub-assembly as shown in the illustration.
Note
After the bolts are removed, do not allow the door glass to fall.
Do not damage the door glass.
REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
*1 | Temporary Bolt |
Loosen the temporary bolt.
Note
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.
Remove the 5 bolts.
Remove the rear door window regulator assembly.
Remove the temporary bolt from the rear door window regulator assembly.
REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" driver, remove the 3 screws and the rear power window regulator motor assembly.