CAUTION:
Remove the luggage door hinge torsion bar while holding the luggage compartment door panel.
REMOVE LUGGAGE COMPARTMENT FLOOR MAT
Remove the luggage compartment floor mat.
REMOVE LUGGAGE COMPARTMENT TRIM COVER LH
Remove the luggage compartment trim cover.
REMOVE LUGGAGE COMPARTMENT TRIM COVER RH
Remove the luggage compartment trim cover.
REMOVE SIDE TRIM BOX
Remove the side trim box.
REMOVE LUGGAGE COMPARTMENT SIDE TRAY (w/ Spare Tire)
Remove the luggage compartment side tray.
REMOVE LUGGAGE COMPARTMENT TRIM BOX (w/o Spare Tire)
Remove the luggage compartment trim box.
REMOVE SPARE WHEEL COVER TRAY (w/o Spare Tire)
Remove the spare wheel cover tray.
REMOVE ROPE HOOK ASSEMBLY
Tech Tips
Use the same procedure for all rope hooks.
Detach the 2 claws and open the cover.
Remove the bolt and rope hook.
REMOVE REAR LUGGAGE COMPARTMENT TRAY BRACKET LH
Remove the clip.
Detach the claw and remove the rear luggage compartment tray bracket.
REMOVE REAR LUGGAGE COMPARTMENT TRAY BRACKET RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Detach the 2 claws and remove the No. 1 luggage compartment trim hook.
REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
*1 | Protective Tape |
Using a screwdriver wrapped with protective tape, detach the 2 claws and remove the No. 1 luggage compartment light assembly.
Disconnect the connector.
REMOVE REAR LUGGAGE COMPARTMENT TRIM COVER
Remove the 5 clips and rear luggage compartment trim cover.
REMOVE REAR FLOOR FINISH PLATE
Remove the 3 clips.
Detach the 6 clips and remove the rear floor finish plate.
REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER
Remove the 3 clips, 2 nuts and front luggage compartment trim cover.
REMOVE ROPE HOOK
Tech Tips
Use the same procedure for both rope hooks.
Rotate the rope hook in the direction indicated by the arrow in the illustration to remove the rope hook.
REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER LH
w/o Power Trunk Lid System:
Using a clip remover, remove the 3 clips and luggage compartment trim inner cover.
w/ Power Trunk Lid System:
Using a clip remover, remove the 2 clips.
Detach the claw and remove the luggage compartment trim inner cover.
REMOVE LUGGAGE COMPARTMENT TRIM INNER COVER RH
Using a clip remover, remove the 3 clips and luggage compartment trim inner cover.
REMOVE LUGGAGE LOCK CONTROL CABLE PLATE (w/ Handle)
Detach the 2 claws and remove the luggage lock control cable plate.
REMOVE LUGGAGE COMPARTMENT DOOR INSIDE HANDLE (w/ Handle)
Disconnect the luggage compartment door inside handle from the luggage door lock control cable.
REMOVE LUGGAGE COMPARTMENT DOOR ASSIST GRIP
Detach the 2 claws and open the cover.
Remove the 2 screws and luggage compartment door assist grip.
REMOVE SWITCH BEZEL (w/ Power Trunk Lid System)
Detach the 2 claws and remove the switch bezel.
REMOVE LUGGAGE COMPARTMENT DOOR COVER
Remove the 15 clips and luggage compartment door cover.
REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH
*A | w/o Power Trunk Lid System |
*B | w/ Power Trunk Lid System |
Remove the 3 clips and luggage compartment door hinge cover.
REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH
Tech Tips
Use the same procedure described for the LH side.
REMOVE LUGGAGE DOOR HINGE TORSION BAR LH
*1 | Washer (90201-10008) |
Install the washer (90201-10008) to SST as shown in the illustration.
Standard | ||||
---|---|---|---|---|
|
Detach the 2 claws and open the cover.
Note
If the cover of the luggage compartment door torsion bar support is opened, replace the luggage compartment door torsion bar support with a new one.
Disconnect the luggage door hinge torsion bar from the luggage compartment door torsion bar support.
Using SST, disconnect the luggage door hinge torsion bar from the luggage compartment door hinge as shown in the illustration.
Detach the 3 guides and remove the luggage door hinge torsion bar.
REMOVE LUGGAGE DOOR HINGE TORSION BAR RH
*1 | Washer (90201-10008) |
Install the washer (90201-10008) to SST as shown in the illustration.
Standard | ||||
---|---|---|---|---|
|
Disconnect the luggage door hinge torsion bar from the luggage compartment door torsion bar support.
Using SST, disconnect the luggage door hinge torsion bar from the luggage compartment door hinge as shown in the illustration.
Detach the 3 guides and remove the luggage door hinge torsion bar.
REMOVE LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT
Rotate the luggage compartment door torsion bar support in the direction indicated by the arrow in the illustration to remove the luggage compartment door torsion bar support.