ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
*1 | Approx. 10 m (32.8 ft.) |
*2 | Approx. 14 m (45.9 ft.) |
Note
Perform measurements on a level surface.
Make sure that no large pieces of metal are within a 10 m (32.8 ft.) x 14 m (45.9 ft.) area in front of the vehicle. If possible, the surrounding area should also be free of large metal objects.
Before adjusting the radar beam axis, prepare the vehicle as follows.
Check the tire pressure and adjust it if necessary.
Remove all excess weight from the vehicle (luggage, heavy objects, etc.).
Remove the cool air intake duct seal Click here.
*1 | Level |
Check and adjust the vertical direction of the radar sensor.
Remove dust, oil and foreign matter from the radar sensor level rack.
Set a level on the radar sensor level rack.
*1 | Vehicle Front |
*2 | Vehicle Left |
*3 | Level |
*4 | Air Bubble |
*5 | Bolt A |
Check that the level's air bubble is within the red frame.
OK |
---|
Level's air bubble is within red frame. |
If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the air bubble is within the red frame.
Tech Tips
The adjustable range within the level's red frame is +/- 0.2°.
The target angle is +0.2° (upward angle of 0.2°).
Result | |||||||
---|---|---|---|---|---|---|---|
|
*1 | Millimeter Wave Radar Sensor |
Adjust the reflector height.
Adjust the reflector so that the center of SST reflector is the same height as the millimeter wave radar sensor.
Tech Tips
Prepare a 10 m (32.8 ft.) string, a string with a sharp-pointed weight (plumb bob) and a 5 m (16.4 ft.) tape measure.
Place the reflector.
Hang the string (with weight) from the center of the vehicle rear emblem. Mark the vehicle rear center point on the ground. Repeat for the front of the vehicle.
*a | Adjust center by moving string to right and left |
*b | Extend string through front center point |
Set one end of the 10 m (32.8 ft.) string on the vehicle rear center point. Run the string over the vehicle front center point to a position 5 m (16.4 ft.) beyond the vehicle front center point, as shown in the illustration. Mark the 5 m (16.4 ft.) position.
Place the reflector (SST) at the marked position.
Note
Perform the operation as precisely as possible.
*a | Reflector Placement Point | *b | Millimeter Wave Radar Sensor Position |
Check the radar beam axis.
When using the GTS:
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on and turn the cruise control main switch on.
Select "Connect to Vehicle".
Select each item on the display screen and proceed to the next screen.
Under "System Selection Menu", select "Radar Cruise".
Select "Utility".
Select "Beam Axis Adjustment" and proceed to the next screen.
Tech Tips
A buzzer will sound for 1 second.
Follow the tester display and continue with the adjustment.
CAUTION:
Do not come within 20 cm (7.87 in.) of the radar sensor.
Note
Turn the cruise control main switch on before pressing Next.
Make sure there is at least 20 cm (7.87 in.) between the radar sensor and any nearby individuals.
Check the following items on the laser cruise divergence data screen.
Note
While using the GTS beam axis adjustment mode, the actual direction and angle of the radar sensor may be different from the GTS data. In such a case, the deviation is displayed on the combination meter multi-information display.
Confirm that the distance value is approximately 5 m (16.4 ft.).
Tech Tips
A value between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.) is indicated.
If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).
Confirm that the left/right side value is between 0.0 m (0.0 ft.) and 6.3 m (20.7 ft.).
Tech Tips
If the distance is 0.0 m (0.0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).
Check and adjust the horizontal direction of the radar sensor.
Check that the divergence of the radar beam axis is 0°.
Standard |
---|
0° (Both right and left) |
If the axis is not as specified, use a screwdriver to adjust bolt B until the divergence of the radar beam axis is 0°.
*1 | Bolt B |
Based on the measured divergence of the beam axis, turn and adjust bolt B for horizontal adjustment of the millimeter wave radar sensor using a screwdriver.
Result | |||||||
---|---|---|---|---|---|---|---|
|
Tech Tips
If the value does not change to 0°, it is possible that the sensor is aiming at something different. Reconfirm that there are no reflective materials in the surrounding area.
Select "Next". The driving learning value is automatically reset.
Tech Tips
A buzzer will sound for 10 seconds or more.
Disconnect the GTS from the DLC3.
Recheck and readjust the vertical direction of the radar sensor.
*1 | Level |
Set a level on the radar sensor level rack.
*1 | Vehicle Front |
*2 | Vehicle Left |
*3 | Level |
*4 | Air Bubble |
*5 | Bolt A |
Check that the level's air bubble is within the red frame.
OK |
---|
Level's air bubble is within the red frame. |
If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the level's air bubble is within the red frame.
Tech Tips
The adjustable range within the red frame is +/- 0.2°.
The target angle is +0.2° (upward angle of 0.2°).
Result | |||||||
---|---|---|---|---|---|---|---|
|
After adjusting the radar beam axis, return the vehicle to its original condition.
If any heavy items were removed from the vehicle, return them (luggage, heavy objects, etc.).
Install the cool air intake duct seal Click here.