Tech Tips
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.
REMOVE LUGGAGE COMPARTMENT FLOOR MAT
Remove the luggage compartment floor mat.
REMOVE LUGGAGE COMPARTMENT TRIM COVER LH
Remove the luggage compartment trim cover.
DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH
Detach the 3 claws and remove the rear door inside handle bezel plug.
REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL ASSEMBLY LH
Detach the 2 clips and 5 claws.
Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.
REMOVE REAR DOOR HOLE COVER
Remove the rear door hole cover.
REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Detach the 8 clips.
Detach the reference boss in the direction indicated by the arrow in the illustration.
Using a screwdriver, detach the 3 claws and remove the rear door trim board.
Tech Tips
Tape the screwdriver tip before use.
*1 | Reference Boss |
*2 | Protective Tape |
Disconnect each connector.
Disconnect the rear door lock remote control cable and rear door inside locking cable.
REMOVE REAR DOOR GLASS INNER WEATHERSTRIP LH
Remove the rear door inner glass weatherstrip.
REMOVE REAR DOOR NO. 1 STIFFENER CUSHION
Remove the rear door No. 1 stiffener cushion.
REMOVE REAR DOOR TRIM COVER LH
Detach the 6 clips and remove the rear door trim cover.
REMOVE REAR SIDE CURTAIN ASSEMBLY LH (w/ Rear Sunshade)
Detach the 4 claws and 2 clips and remove the rear side curtain.
REMOVE REAR DOOR FRAME GARNISH LH
Detach the 2 clips and remove the rear door frame garnish.
REMOVE REAR DOOR ARMREST SET BRACKET LH
Remove the 2 screws and rear door armrest set bracket.
REMOVE REAR DOOR SERVICE HOLE COVER LH
Pull out the rear door lock remote control cable and rear door inside locking cable from the rear door service hole cover, and then remove the rear door service hole cover.
Tech Tips
Remove any remaining butyl tape from the rear door panel.
REMOVE REAR NO. 2 SPEAKER ASSEMBLY
Disconnect the connector.
Remove the screw.
Detach the clamp and remove the rear No. 2 speaker assembly.
Note
Do not touch the cone of the speaker.
REMOVE REAR DOOR GLASS RUN LH
Remove the front side of the rear door glass run.
REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH
Temporarily install the rear power window regulator switch assembly with rear door armrest base panel.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the rear door window regulator so that the rear door glass channel can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
Remove the rear power window regulator switch assembly with rear door armrest base panel.
Partially remove the rear door glass run as shown in the illustration.
Remove the screw and 2 bolts.
Remove the rear door rear lower window frame together with the rear door glass run as shown in the illustration.
Remove the rear door rear lower window frame from the rear door glass run.
REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Remove the rear door quarter window glass.
REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Remove the rear door glass from the rear door window regulator as shown in the illustration.
Note
Do not damage the door glass.
REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Disconnect the connector.
*1 | Temporary Bolt |
Loosen the temporary bolt.
Note
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and become damaged.
Remove the 3 bolts and rear door window regulator.
Remove the temporary bolt from the rear door window regulator.
REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
Using a T25 "TORX" driver, remove the 3 screws and power window regulator motor assembly LH.