DATA LIST
Tech Tips
Using the intelligent tester to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the power switch ON (IG).
Turn the tester on.
Enter the following menus:
Select: Body / (desired system) / Data List.
According to the display on tester, read the "Data List".
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
D Door P/W Auto SW | Driver side power window auto UP/DOWN switch signal / ON or OFF | ON: Driver side power window auto UP/DOWN switch on master switch operated OFF: Driver side power window switch on master switch not operated |
- |
P Door P/W Auto SW | Front passenger side power window remote auto UP/DOWN switch signal / ON or OFF | ON: Front passenger side power window remote auto UP/DOWN switch on master switch operated OFF: Front passenger side power window switch on master switch not operated |
- |
RR Door P/W Auto SW | Rear power window RH remote auto UP/DOWN switch signal / ON or OFF | ON: Rear power window RH remote auto UP/DOWN switch on master switch operated OFF: Rear power window RH switch on master switch not operated |
- |
RL Door P/W Auto SW | Rear power window LH remote auto UP/DOWN switch signal / ON or OFF | ON: Rear power window LH remote auto UP/DOWN switch on master switch operated OFF: Rear power window LH switch on master switch not operated |
- |
P Door P/W Up SW | Front passenger side power window remote manual UP switch signal / ON or OFF | ON: Front passenger side power window remote manual UP switch on master switch operated OFF: Front passenger side power window switch on master switch not operated |
- |
RR Door P/W Up Switch | Rear power window RH remote manual UP switch signal / ON or OFF | ON: Rear power window RH remote manual UP switch on master switch operated OFF: Rear power window RH switch on master switch not operated |
- |
RL Door P/W Up Switch | Rear power window LH remote manual UP switch signal / ON or OFF | ON: Rear power window LH remote manual UP switch on master switch operated OFF: Rear power window LH switch on master switch not operated |
- |
P Door P/W Down SW | Front passenger side power window remote manual DOWN switch signal / ON or OFF | ON: Front passenger side power window remote manual DOWN switch on master switch operated OFF: Front passenger side power window switch on master switch not operated |
- |
RR Door P/W Down SW | Rear power window RH remote manual DOWN switch signal / ON or OFF | ON: Rear power window RH remote manual DOWN switch on master switch operated OFF: Rear power window RH switch on master switch not operated |
- |
RL Door P/W Down SW | Rear power window LH remote manual DOWN switch signal / ON or OFF | ON: Rear power window LH remote manual DOWN switch on master switch operated OFF: Rear power window LH switch on master switch not operated |
- |
Window Lock Switch Status | Power window LOCK switch / ON or OFF | ON: Power window lock switch LOCK position OFF: Power window lock switch UNLOCK position |
- |
Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs will be displayed | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
D Door P/W Auto SW | Driver side power window auto UP/DOWN switch signal / ON or OFF | ON: Driver side power window auto UP/DOWN switch on master switch operated OFF: Driver side power window switch on master switch not operated |
- |
D Door P/W Up SW | Driver side power window MANUAL UP switch signal / ON or OFF | ON: Driver side power window manual UP switch on master switch operated OFF: Driver side power window switch on master switch not operated |
- |
D Door P/W Down SW | Driver side power window MANUAL DOWN switch signal / ON or OFF | ON: Driver side power window manual DOWN switch on master switch operated OFF: Driver side power window switch on master switch not operated |
- |
Glass Position (Close-1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (1/4-2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (2/4-3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (3/4-Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs will be displayed | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
P Door P/W Auto SW | Front passenger side power window auto UP/DOWN switch signal / ON or OFF | ON: Front passenger side power window auto UP/DOWN switch operated OFF: Front passenger side power window switch not operated |
- |
P Door P/W Up SW | Front passenger side power window manual UP switch signal / ON or OFF | ON: Front passenger side power window manual UP switch operated OFF: Front passenger side power window switch not operated |
- |
P Door P/W Down SW | Front passenger side power window manual DOWN switch signal / ON or OFF | ON: Front passenger side power window manual DOWN switch operated OFF: Front passenger side power window switch not operated |
- |
Glass Position (Close-1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (1/4-2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (2/4-3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (3/4-Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs will be displayed | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
RL Door P/W Auto SW | Rear power window LH auto UP/DOWN switch signal / ON or OFF | ON: Rear power window LH auto UP/DOWN switch operated OFF: Rear power window LH switch not operated |
- |
RL Door P/W Up SW | Rear power window LH manual UP switch signal / ON or OFF | ON: Rear power window LH manual UP switch operated OFF: Rear power window LH switch not operated |
- |
RL Door P/W Down SW | Rear power window LH manual DOWN switch signal / ON or OFF | ON: Rear power window LH manual DOWN switch operated OFF: Rear power window LH switch not operated |
- |
Glass Position (Close-1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (1/4-2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (2/4-3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (3/4-Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs will be displayed | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
RR Door P/W Auto SW | Rear power window RH auto UP/DOWN switch signal / ON or OFF | ON: Rear power window RH auto UP/DOWN switch operated OFF: Rear power window RH switch not operated |
- |
RR Door P/W Up SW | Rear power window RH manual UP switch signal / ON or OFF | ON: Rear power window RH manual UP switch operated OFF: Rear power window RH switch not operated |
- |
RR Door P/W Down SW | Rear power window RH manual DOWN switch signal / ON or OFF | ON: Rear power window RH manual DOWN switch operated OFF: Rear power window RH switch not operated |
- |
Glass Position (Close-1/4) | Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (1/4-2/4) | Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (2/4-3/4) | Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Glass Position (3/4-Open) | Margin for jam protection triggering force of window glass within range of 3/4 to fully open position / OK or Caution | OK: Margin is sufficient during manual UP operation Caution: May be displayed even when no resistance is applied in each position. In this case, there is a foreign object stuck in that position. |
- |
Number of Trouble Codes | Number of trouble codes / Min.: 0, Max.: 255 |
Number of DTCs will be displayed | - |
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
Communication D-Door Motor | Connection status between power window regulator motor (for driver side) and main body ECU / OK or STOP | OK: Connection Stop: No connection |
- |
Communication P-Door Motor | Connection status between power window regulator motor (for front passenger side) and main body ECU / OK or STOP | OK: Connection Stop: No connection |
- |
Communication RR-Door Motor | Connection status between rear power window regulator motor RH and main body ECU / OK or STOP | OK: Connection Stop: No connection |
- |
Communication RL-Door Motor | Connection status between rear power window regulator motor LH and main body ECU / OK or STOP | OK: Connection Stop: No connection |
- |
Communication Master SW | Connection status between master switch and main body ECU / OK or STOP | OK: Connection Stop: No connection |
- |
D Door Courtesy SW | Driver side door courtesy switch signal / ON or OFF | ON: Driver door open OFF: Driver door closed |
- |
P Door Courtesy SW | Front passenger side door courtesy switch signal / ON or OFF | ON: Front passenger door open OFF: Front passenger door closed |
- |
RL Door Courtesy SW | Rear RH side door courtesy switch signal / ON or OFF | ON: Rear RH side door open OFF: Rear RH side door closed |
- |
RR Door Courtesy SW | Rear LH side door courtesy switch signal / ON or OFF | ON: Rear LH side door open OFF: Rear LH side door closed |
- |
ACTIVE TEST
Tech Tips
Using the intelligent tester to perform Active Test allows relays, VSVs, actuators and parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.
Connect the intelligent tester to the DLC3.
Turn the power switch ON (IG).
Turn the tester on.
Enter the following menus:
Select: Body / (desired system) / Active Test.
According to the display on tester, perform the "Active Test".
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function does not operate.
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Power Window | Driver side power window | UP or OFF (OFF) | - |
Power Window | Driver side power window | DOWN or OFF (OFF) | - |
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Power Window | Front passenger side power window | UP or OFF (OFF) | - |
Power Window | Front passenger side power window | DOWN or OFF (OFF) | - |
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Power Window | Rear LH side power window | UP or OFF (OFF) | - |
Power Window | Rear LH side power window | DOWN or OFF (OFF) | - |
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Power Window | Rear RH side power window | UP or OFF (OFF) | - |
Power Window | Rear RH side power window | DOWN or OFF (OFF) | - |