DESCRIPTION
The main body ECU and front multiplex network door ECU controls the interior illumination lights.
WIRING DIAGRAM
INSPECTION PROCEDURE
Note
First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this DTC.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
PROCEDURE
CHECK OPERATION
Check the operation of each light.
Result | Proceed to |
---|---|
Front door illumination does not illuminates | A |
Rear door illumination and interior foot light do not illuminates | B |
B |
PERFORM ACTIVE TEST USING GTS (ILLUMINATION LIGHT) Click here |
A |
PERFORM ACTIVE TEST USING GTS (ILLUMINATION LIGHT)
Using the GTS, perform the Active Test Click here.
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Inside Handle Light | Front door inside handle illumination light LH | ON/OFF | - |
Interior Illumination Light | Front door ambient light LH | ON/OFF | - |
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Inside Handle Light | Front door inside handle illumination light RH | ON/OFF | - |
Interior Illumination Light | Front door ambient light RH | ON/OFF | - |
OK |
---|
Front door inside handle illumination light and front door ambient light illuminates. |
Result | Proceed to |
---|---|
OK | A |
NG (Front door inside handle illumination light does not illuminates) | B |
NG (No. 1 interior illumination light [front door ambient light] does not illuminates) | C |
B |
INSPECT FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY Click here |
C |
INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT (FRONT DOOR AMBIENT LIGHT) Click here |
A |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here
INSPECT FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY
Remove the front door inside handle illumination light Click here.
Inspect the front door inside handle illumination light Click here.
NG |
REPLACE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY Click here |
OK |
CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU - FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT)
for LH:
Disconnect the Q19 front multiplex network door ECU LH connector.
Disconnect the Q27 front door inside handle illumination light LH connector.
for RH:
Disconnect the Q4 front multiplex network door ECU RH connector.
Disconnect the Q12 front door inside handle illumination light RH connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
for LH | |||||||||||||||
|
|||||||||||||||
for RH | |||||||||||||||
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
REPLACE FRONT MULTIPLEX NETWORK DOOR ECU Click here
INSPECT NO. 1 INTERIOR ILLUMINATION LIGHT (FRONT DOOR AMBIENT LIGHT)
Remove the No. 1 interior illumination light (front door ambient light) Click here.
Inspect the No. 1 interior illumination light (front door ambient light) Click here.
NG |
REPLACE NO. 1 INTERIOR ILLUMINATION LIGHT (FRONT DOOR AMBIENT LIGHT) Click here |
OK |
CHECK HARNESS AND CONNECTOR (FRONT MULTIPLEX NETWORK DOOR ECU - NO. 1 INTERIOR ILLUMINATION LIGHT [FRONT DOOR AMBIENT LIGHT])
for LH:
Disconnect the Q18 and Q19 front multiplex network door ECU LH connectors.
Disconnect the Q29 No. 1 interior illumination light LH (front door ambient light) connector.
for RH:
Disconnect the Q3 and Q4 front multiplex network door ECU RH connectors.
Disconnect the Q14 No. 1 interior illumination light RH (front door ambient light) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
for LH | |||||||||||||||
|
|||||||||||||||
for RH | |||||||||||||||
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
REPLACE FRONT MULTIPLEX NETWORK DOOR ECU Click here
PERFORM ACTIVE TEST USING GTS (ILLUMINATION LIGHT)
Using the GTS, perform the Active Test Click here.
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Fr Foot Light | Rear door inside handle illumination light, rear door ambient light, rear interior foot light and front interior foot light | ON/OFF | - |
OK |
---|
Rear door inside handle illumination light, rear door ambient light, rear interior foot light and front interior foot light illuminates. |
NG |
CHECK HARNESS AND CONNECTOR (REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT - MAIN BODY ECU AND BODY GROUND) Click here |
OK |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here
CHECK HARNESS AND CONNECTOR (REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT - MAIN BODY ECU AND BODY GROUND)
Disconnect the N13 main body ECU connector.
Disconnect the S4 rear door inside handle illumination light connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage | ||||||
---|---|---|---|---|---|---|
|
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here