STEERING LOCK SYSTEM, Diagnostic DTC:B2782

DTC Code DTC Name
B2782 Power Source Control ECU Malfunction

DESCRIPTION

The certification ECU (smart key ECU assembly) has a power source mode switching function.

This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU is determined to be abnormal.

Tech Tips

The steering lock ECU is not connected to the CAN communication system. However, the steering lock ECU is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).

DTC No. Detection Condition Trouble Area DTC Output Confirmation Operation
B2782

Either condition is met (1-trip detection logic*):


  • The steering lock motor activation command circuit has a short circuit.

  • The steering lock motor activation command circuit has an open circuit.

Tech Tips

If the power supply signal from the LIN communication line does not match the power supply signal from the direct line, the system is determined to be malfunctioning.


  • Steering lock ECU (Steering lock actuator assembly)

  • Certification ECU (Smart key ECU assembly)

  • Harness or connector

Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the key.)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. Prohibits the engine from being started (the engine does not crank).
Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2782 - -

WIRING DIAGRAM

B007VOFE26

INSPECTION PROCEDURE

Note


  • When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting Click here.

  • When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected Click here.

  • After performing repairs, perform the DTC output confirmation operation, and then confirm that no DTCs are output again Click here.

  • When replacing the steering lock ECU (steering lock actuator assembly), registration must be performed (Refer to the Service Bulletin).

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (GROUND)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

    3. B007OMNE77
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Steering Lock ECU (Steering Lock Actuator Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H80-1 (GND) - Body ground Always Below 1 Ω

    NG
    OK
  2. INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)


    1. Reconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

    2. Turn the engine switch off, make sure that the steering is unlocked and move the shift lever to P.

    3. B007P4TE21
      Text in Illustration
      *a

      Component with harness connected

      (Steering Lock ECU (Steering Lock Actuator Assembly))

      *b Steering lock motor not operating
      *c Steering lock motor operating

      Check the signal waveform according to the condition(s) in the table below.

      Standard Frequency
      Item Content
      Tester Connection H80-3 (IGE) - H80-1 (GND)
      Tool Setting 2 V/DIV., 200 ms./DIV.
      Vehicle Condition Steering lock motor not operating → Operating → Not operating

      Tech Tips


      • When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.

      • In order to take measurements when the lock motor is operating, perform either of the following operations:


        • To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.

        • To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.


    NG
    OK
  3. CLEAR DTC AND DATA LIST MALFUNCTION RECORD


    1. Clear the DTCs Click here.

    2. Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.

      Note

      After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notices before proceeding with work Click here.


    NEXT
  4. READ VALUE USING GTS (POWER SUPPLY SHORT)


    1. Perform the DTC output confirmation operation.

    2. Check if DTC B2782 is output Click here.

      Result
      Result Proceed to
      DTC B2782 is not output. A
      DTC B2782 is output. B

    B
    A
  5. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))


    1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Disconnect the H80 steering lock ECU (steering lock actuator assembly) connector.

    3. Disconnect the B75 certification ECU (smart key ECU assembly) connector.

    4. Check for deformation and corrosion of the connector case and terminals.

      OK
      There is no deformation or corrosion of the connector case or terminals.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H80-3 (IGE) - B75-17 (SLR+) Always Below 1 Ω
      H80-3 (IGE) - Body ground 10 kΩ or higher
      B75-17 (SLR+) - Body ground

    NG
    OK