INSTALL INSTRUMENT PANEL STAY
Engage the claw to install the instrument panel stay.
INSTALL INSTRUMENT PANEL CLIP
Engage the 4 claws to install the 4 instrument panel clips.
INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Engage the 5 claws.
Note
Do not allow the wire harness to get caught in the claws.
Engage the 2 clamps.
Install the 2 passenger airbag bolts <A> or <B>.
Install the 6 bolts <C> and nut <G>.
Engage the 2 claws and install the cooler thermistor.
Engage the clamps.
Connect the connectors and install the instrument panel safety pad assembly.
CONNECT NO. 2 INSTRUMENT PANEL WIRE
Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the connector.
Note
When connecting the airbag connector, take care not to damage the airbag wire harness.
INSTALL NO. 1 CONSOLE BOX DUCT
Install the No. 1 console box duct with the clip.
INSTALL NO. 2 CONSOLE BOX DUCT
Install the No. 2 console box duct with the 2 clips.
INSTALL FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker)
Connect the connector.
Install the front stereo component speaker assembly with the 2 bolts.
Tech Tips
Install the bolts in the order shown in the illustration.
INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 7 claws and 2 clips to install the No. 3 instrument panel speaker panel sub-assembly.
INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Connect the connector.
Engage the 4 claws and 2 clips to install the No. 2 instrument panel register assembly.
INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Connect the connector.
Engage the 7 claws and 2 clips to install the No. 1 instrument panel register assembly.
INSTALL FRONT PILLAR GARNISH LH
Remove the protective cover.
Make sure that the front pillar garnish clip is not damaged.
Note
If there is any damage, replace the garnish clip with a new one.
When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.
Engage the guide.
Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.
Tech Tips
Tape the tips of the needle-nosed pliers before use.
Engage the 2 clips to install the front pillar garnish LH.
INSTALL FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure as for the LH side Click here.
INSTALL POWER SOURCE CONTROL ECU (for LHD)
Connect the connector.
Install the power source control ECU with the bolt and 2 nuts.
INSTALL MULTI-MEDIA INTERFACE ECU WITH BRACKET (for RHD)
Install the multi-media interface ECU with bracket with the 2 nuts and bolt.
Connect each connector.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Connect the connectors.
Engage the 2 claws.
Install the glove compartment door assembly with the 5 screws <D>.
INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY
Check that the engine switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the front passenger side knee airbag connector to the front passenger side knee airbag assembly.
Note
When connecting the airbag connector, take care not to damage the airbag wire harness.
Install the front passenger side knee airbag assembly with the 3 bolts and claw.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Engage the 4 clips to install the No. 2 instrument panel under cover sub-assembly.
INSTALL SIDE INSTRUMENT PANEL RH
Engage the 5 claws and 3 clips to install the side instrument panel RH.
INSTALL FRONT DOOR OPENING TRIM COVER RH
Tech Tips
Use the same procedure as for the LH side Click here.
INSTALL FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure as for the LH side Click here.
INSTALL COMBINATION METER ASSEMBLY
Connect the connectors.
Engage the 2 claws and install the combination meter assembly.
INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Install the instrument cluster finish panel sub-assembly with the 2 screws <F> and 2 clips.
INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
Check that the engine switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the driver side knee airbag connector to the driver side knee airbag assembly.
Note
When connecting the airbag connector, take care not to damage the airbag wire harness.
Temporarily install the driver side knee airbag assembly with the 2 pins.
Install the driver side knee airbag assembly with the 4 bolts.
Install the hood lock control cable with the claw.
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY
Connect the connectors.
Engage the 7 clips to install the lower instrument panel finish panel sub-assembly.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connectors.
Insert the No. 1 instrument panel under cover sub-assembly into the guide as shown in the illustration.
Engage the 2 claws.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <D>.
INSTALL SIDE INSTRUMENT PANEL LH
Engage the 5 claws and 3 clips to install the side instrument panel LH.
INSTALL FRONT DOOR OPENING TRIM COVER LH
Engage the 4 claws and install the front door opening trim cover LH.
INSTALL FRONT DOOR SCUFF PLATE LH
Engage the 4 clips.
Engage the 7 claws and install the front door scuff plate LH.
INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
INSTALL STEERING COLUMN COVER
Engage the 4 clips and 2 guides to install the upper steering column cover onto the instrument panel cluster finish panel.
Engage the claw to install the upper steering column cover.
Engage the 2 claws to install the lower steering column cover.
Note
Do not damage the tilt and telescopic switch.
Install the 3 screws.
ADJUST SPIRAL CABLE SUB-ASSEMBLY
Check that the engine switch is off.
Check that the battery negative (-) cable is disconnected.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Rotate the spiral cable counterclockwise slowly by hand until it stops.
Note
Do not turn the spiral cable using the airbag wire harness.
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
Note
Do not turn the spiral cable using the airbag wire harness.
Tech Tips
The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.
INSTALL STEERING WHEEL ASSEMBLY
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
INSTALL STEERING PAD
Check that the engine switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the 2 airbag connectors to the steering pad.
Note
When connecting the airbag connector, take care not to damage the airbag wire harness.
Be sure to only connect the connectors to each corresponding color.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of each "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
Using a T30 "TORX" socket wrench, tighten the 2 "TORX" screws.
INSTALL LOWER NO. 3 STEERING WHEEL COVER
Install the lower No. 3 steering wheel cover with the claw.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
Install the lower No. 2 steering wheel cover with the claw.
INSTALL INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Navigation System)
Connect each connector.
Install the integration control panel with radio receiver assembly with the 4 bolts.
INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Navigation System)
Connect each connector.
Install the display and navigation module display with radio receiver assembly with the 4 bolts.
INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL
Engage the 4 claws to install the center lower instrument cluster finish panel.
INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
for LHD:
Connect the connector.
for RHD:
Connect the connector.
Engage the 3 clamps.
Engage the 11 claws to install the No. 3 instrument panel register assembly.
INSTALL CONSOLE BOX
Engage the 2 claws and 2 clips.
Connect each connector.
Install the 2 bolts.
Install the 2 bolts.
Connect the 2 connectors.
Engage the 2 clamps.
Install the 2 bolts.
INSTALL CONSOLE BOX REGISTER ASSEMBLY (w/ Ashtray)
Engage the 2 claws and 4 clips to install the console box register assembly.
INSTALL CONSOLE BOX REGISTER ASSEMBLY (w/o Ashtray)
Engage the 2 claws and 4 clips to install the console box register assembly.
INSTALL REAR ASH RECEPTACLE ASSEMBLY (w/ Ashtray)
Install the rear ash receptacle assembly.
INSTALL FRONT ASH RECEPTACLE BOX SUB-ASSEMBLY (w/ Ashtray)
Connect the connectors.
Insert the protruding parts of the front ash receptacle box sub-assembly into the 2 guide holes as shown in the illustration.
Install the front ash receptacle box sub-assembly with the 2 screws <E>.
INSTALL INSTRUMENT PANEL BOX ASSEMBLY (w/o Ashtray)
Connect the connectors.
Insert the protruding parts of the instrument panel box assembly into 2 guide holes as shown in the illustration.
Install the instrument panel box assembly with the 2 screws <E>.
INSTALL CONSOLE PANEL SUB-ASSEMBLY
Connect the connectors.
Engage the 8 clips to install the console panel sub-assembly.
INSTALL UPPER NO. 2 CONSOLE PANEL GARNISH
Engage the claw and 2 clips to install the upper No. 2 console panel garnish as shown in the illustration.
INSTALL UPPER NO. 1 CONSOLE PANEL GARNISH
Engage the claw and 2 clips to install the upper No. 1 console panel garnish as shown in the illustration.
INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob clockwise and install the shift lever knob sub-assembly.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
INSPECT STEERING PAD
With the steering pad installed on the vehicle, perform a visual check. If there are any following defects, replace the steering pad with a new one:
Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.
Make sure that the horn sounds.
Tech Tips
If the horn does not sound, inspect the horn system Click here.
INSPECT SRS WARNING LIGHT
Inspect the SRS warning light Click here.