DESCRIPTION
The ECM constantly uses 5 V from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
When the VC circuit is shorted, the microprocessor in the ECM and sensors that are supplied power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.
Tech Tips
Under normal conditions, the MIL is illuminated for several seconds when the engine switch is first turned on (IG). The MIL goes off when the engine is started.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
CHECK MIL
Check that Malfunction Indicator Lamp (MIL) illuminates when turning the engine switch on (IG).
OK |
---|
MIL lights up. |
NG |
CHECK CONNECTION BETWEEN GTS AND ECM Click here |
OK |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here
CHECK CONNECTION BETWEEN GTS AND ECM
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and GTS on.
Check the communication between the GTS and ECM.
Result | ||||||
---|---|---|---|---|---|---|
|
B |
GO TO MIL CIRCUIT Click here |
A |
CHECK MIL (THROTTLE POSITION SENSOR)
Disconnect the throttle body with motor connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the throttle body with motor connector.
Tech Tips
Perform "Inspection After Repair" after replacing the throttle body with motor Click here.
B |
REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY Click here |
A |
CHECK MIL (ACCELERATOR PEDAL SENSOR)
Disconnect the accelerator pedal position sensor connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the accelerator pedal position sensor connector.
B |
REPLACE ACCELERATOR PEDAL ASSEMBLY Click here |
A |
CHECK MIL (VVT SENSOR FOR INTAKE SIDE BANK 1)
Disconnect the VVT sensor for intake side bank 1 connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the VVT sensor for intake side bank 1 connector.
B |
REPLACE VVT SENSOR FOR INTAKE SIDE BANK 1 Click here |
A |
CHECK MIL (VVT SENSOR FOR EXHAUST SIDE BANK 1)
Disconnect the VVT sensor for exhaust side bank 1 connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the VVT sensor for exhaust side bank 1 connector.
B |
REPLACE VVT SENSOR FOR EXHAUST SIDE BANK 1 Click here |
A |
CHECK MIL (VVT SENSOR FOR INTAKE SIDE BANK 2)
Disconnect the VVT sensor for intake side bank 2 connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the VVT sensor for intake side bank 2 connector.
B |
REPLACE VVT SENSOR FOR INTAKE SIDE BANK 2 Click here |
A |
CHECK MIL (VVT SENSOR FOR EXHAUST SIDE BANK 2)
Disconnect the VVT sensor for exhaust side bank 2 connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the VVT sensor for exhaust side bank 2 connector.
B |
REPLACE VVT SENSOR FOR EXHAUST SIDE BANK 2 Click here |
A |
CHECK MIL (FUEL PRESSURE SENSOR)
Disconnect the fuel pressure sensor connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the fuel pressure sensor connector.
B |
REPLACE FUEL PRESSURE SENSOR Click here |
A |
CHECK MIL (CANISTER PUMP MODULE)
Disconnect the canister pump module connector.
Turn the engine switch on (IG).
Check the MIL.
Result | ||||||
---|---|---|---|---|---|---|
|
Reconnect the canister pump module connector.
B |
REPLACE CANISTER PUMP MODULE Click here |
A |
CHECK HARNESS AND CONNECTOR
Disconnect the throttle body with motor connector.
Disconnect the accelerator pedal position sensor connector.
Disconnect the VVT sensor for intake side bank 1 connector.
Disconnect the VVT sensor for exhaust side bank 1 connector.
Disconnect the VVT sensor for intake side bank 2 connector.
Disconnect the VVT sensor for exhaust side bank 2 connector.
Disconnect the fuel pressure sensor connector.
Disconnect the canister pump module connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
Standard Resistance (Check for Short) | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Reconnect the ECM connectors.
Reconnect the canister pump module connector.
Reconnect the fuel pressure sensor connector.
Reconnect the VVT sensor for exhaust side bank 2 connector.
Reconnect the VVT sensor for intake side bank 2 connector.
Reconnect the VVT sensor for exhaust side bank 1 connector.
Reconnect the VVT sensor for intake side bank 1 connector.
Reconnect the accelerator pedal position sensor connector.
Reconnect the throttle body with motor connector.
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
REPLACE ECM Click here