AUTOMATIC TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) REMOVAL

Note

If automatic transmission parts are replaced, refer to the Parts Replacement Compensation Table to determine if any additional operations are necessary Click here.


  1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  2. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH


    1. A01I16SE01

      Using SST, remove the front drive shaft assembly LH.

      SST
      09520-00031
      09520-01010

      Note


      • Do not damage the transaxle case oil seal.

      • Do not damage the front axle inboard joint boot.

      • Do not drop the front drive shaft assembly LH.

  3. REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH


    1. A01HZI2

      Using a screwdriver, remove the front drive shaft hole snap ring LH.

  4. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH


    1. A01I1GA

      Separate the bearing bracket hole snap ring from the drive shaft bearing bracket.

    2. Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

      Note


      • Do not damage the front transaxle case oil seal.

      • Do not damage the front axle inboard joint boot.

      • Do not drop the front drive shaft assembly RH.

    3. Remove the bearing bracket hole snap ring from the front drive shaft assembly RH.

  5. REMOVE FRONT FRAME ASSEMBLY

    for 2GR-FE: Click here

    for 2AR-FE: Click here

  6. REMOVE WIRING HARNESS CONNECTOR


    1. A01HZOF

      Disconnect the wire harness clamp.

    2. Turn the lock lever and disconnect the connector from the wiring harness connector.

    3. A01HZ17

      Remove the 2 bolts and wiring harness connector from the automatic transaxle assembly.

  7. SEPARATE WIRE HARNESS


    1. A01HZB8

      Remove the bolt and ground cable.

    2. Separate the park/neutral position switch connector and 7 wire harness clamps.

  8. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY


    1. Using the transmission jack attachment, set the automatic transaxle assembly on a transmission jack.

      Note


      • Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.

      • To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the automatic transaxle assembly.

      • Hold the engine assembly with a suitable adapter, such as a rope, during the operation.

    2. A01HYNA

      Remove the 9 bolts and automatic transaxle assembly.

      Note

      To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine.

  9. REMOVE TRANSMISSION OIL COOLER


    1. A01I218E01
      Text in Illustration
      *1 No. 1 Oil Cooler Inlet Hose
      *2 No. 1 Oil Cooler Outlet Hose

      Remove the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose.

    2. A01I23H

      Remove the 3 bolts and transmission oil cooler from the front engine mounting bracket.

  10. REMOVE FRONT ENGINE MOUNTING BRACKET


    1. A01I0ET

      Remove the 3 bolts and front engine mounting bracket from the automatic transaxle assembly.

  11. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. A01I0W3

      Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.

  12. REMOVE WIRE HARNESS CLAMP BRACKET


    1. A01I0RE

      Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle assembly.

  13. REMOVE TRANSMISSION CASE PLUG ASSEMBLY


    1. A01HZMF

      Remove the transmission case plug assembly from the automatic transaxle assembly.

    2. Remove the O-ring from the transmission case plug assembly.

  14. REMOVE TORQUE CONVERTER ASSEMBLY


    1. A01I0W1

      Remove the torque converter assembly from the automatic transaxle assembly.