ECD SYSTEM (w/o DPF) REGISTRATION


  1. LEARNING VALUES CONFIRMATION

    This procedure uses the GTS to display the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the ECM.

    B007P39E02

    Tech Tips


    • B007V4D

      A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values confirmation.

    4. B007QOY

      Press "Next".

    5. B007W9O

      Press "Next" again to proceed.

    6. B007Q0D

      Select the value to confirm and press "Next".

    7. When the next screen is displayed, confirm the contents and press "Exit".

      B007QM9
  2. LEARNING VALUES SAVE

    This procedure uses the GTS to save the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the ECM in the GTS depending on the components being replaced.

    B007QKSE02

    Tech Tips


    • When replacing the engine assembly or the injector assembly together with the ECM, this function automatically determines the data which can be transferred (old data) and saves the data in the GTS.

    • B007OJW

      When there is no data to read from the ECM, manually perform the procedure to register each compensation code and learning value in the ECM.

    • B007SPH

      A malfunction may occur when reading the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values save.

    4. B007U88

      Press "Next".

    5. B007WBU

      Press "Next" again to proceed.

    6. B007RUL

      Select any components being replaced and press "Next". If no applicable components are displayed, press "Next" without selecting anything.

    7. B007S9P

      If the overwrite confirmation screen is displayed, press "Overwrite".

    8. B007PZI

      When the operation is finished, confirm the date and time of the save operation, and then press "Exit".

  3. LEARNING VALUES WRITE

    This procedure uses the GTS to write all of the learned values (injector compensation code, pilot quantity learning value and crank time compensation learning value) stored in the GTS to the ECM.

    B007S7WE02

    Tech Tips


    • B007SAS

      A malfunction may occur when writing the values if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

      Note

      Do not start the engine.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Learning values write.

    4. B007SXZ

      Press "Next".

    5. B007WDL

      Press "Next" again to proceed.

    6. B007PY5

      If the "Error Learning Values Write" screen indicating a problem with the saved values or that there are no saved values is displayed, perform "Learning Values Save" again.

    7. B007SQV

      Confirm the date and time of the save operation, and then press "Yes".

    8. B007RLG

      Confirm the contents, and then press "Next".

    9. B007UHZ

      If any instructions are displayed on the GTS, manually perform the procedure to register each applicable compensation code or learning value in the ECM.

    10. Clear the DTCs Click here.

  4. INPUT INJECTOR COMPENSATION CODE(S) INTO ECM

    B007Q42E04

    Note


    • When an injector assembly is replaced, the new injector compensation code must be input into the ECM. When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

    • Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly. If an incorrect injector compensation code is input into the ECM, the engine assembly may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

    • When an injector compensation code is input into the ECM, the pilot quantity learning values stored in the ECM are initialized. Also, DTC P1601 is stored when the pilot quantity learning values are initialized.


    1. After replacing one or more injectors assembly with new ones, input the compensation codes of the injector assemblies into the ECM as follows:

      Tech Tips


      • Each injector assembly has different fuel injection characteristics. In order to optimize the fuel injections, the ECM uses the compensation codes to balance the different fuel injections between each injector assembly.

      • When one or more injector assemblies are replaced, input the injector compensation codes, perform pilot quantity learning, and then clear the DTCs.

      • When the ignition switch is turned to ON after replacing the ECM, DTC P1601 is stored. This indicates that one or more injector compensation codes need to be registered. Manually clear the DTC upon completion of pilot quantity learning.


      1. Input the compensation codes, which are imprinted on the head portions of the new injector assemblies, into the GTS.

      2. Input the new compensation codes into the ECM using the GTS.

      3. Turn the GTS off and turn the ignition switch off.

      4. Wait for at least 30 seconds.

      5. Turn the ignition switch to ON and turn the GTS on.

      6. Perform pilot quantity learning.

      7. Clear DTC P1601 stored in the ECM using the GTS Click here.

        Note

        If the DTCs are cleared without performing pilot quantity learning, DTC P1601 is stored immediately after clearing DTCs.

    2. Register compensation codes.

      B007QYZE04

      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

        Note

        Do not start the engine.

      3. Turn the GTS on.

      4. B007VML

        Enter the following menus: Powertrain / Engine and ECT / Utility / Injector Compensation.

      5. Press "Next".

      6. B007PX2

        Press "Next" again to proceed.

      7. B007V1B

        Select "Set Compensation Code".

      8. Press "Next".

      9. B007S6A

        Select the number of the cylinder corresponding to the injector compensation code that you want to register.

      10. Press "Next".

      11. B007PYP

        Register compensation code.


        1. Press "Input".

        2. B007QZX

          Manually input the cylinder compensation code using the keyboard on the GTS screen. The code is a 30-digit, alphanumeric value printed on the head portion of the injector assembly.

          Tech Tips

          Each injector compensation code is unique. The compensation code for each selected cylinder must be input into the GTS correctly.

        3. Confirm that the compensation code for the selected cylinder is correct, and then press "OK".

      12. B007VI0

        Check that the compensation code displayed on the screen is correct by comparing it with the 30-digit alphanumeric value on the head portion of the injector assembly.

        Note

        If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.

        Tech Tips


        • If an incorrect compensation code is input or read, return to the "Input Value" screen by pressing "Input".

        • The saving process may fail due to a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and repeat this operation.

      13. Press "Next" to register the compensation code in the ECM.

        Tech Tips


        • If the registration process fails, the compensation code may be incorrect. Check the compensation code again.

        • If the input compensation code fails to register even though it is input correctly, there may be a problem with the wire harness or a bad connection with the DLC3. Check the wire harness and DLC3 connection. If no problem is found with either, the ECM may be malfunctioning. Check the ECM and restart this operation.

      14. B007PCS

        If you want to continue with other compensation code registrations, press "Next". To finish the registration, press "Exit".

      15. Turn the ignition switch off, and then turn the GTS off.

      16. Wait for at least 30 seconds.

      17. Turn the ignition switch to ON, and then turn the GTS on.

      18. Perform pilot quantity learning.

      19. Clear DTC P1601 stored in the ECM using the GTS Click here.

        Note

        If the DTCs are cleared without performing pilot quantity learning, DTC P1601 is stored immediately after clearing DTCs.

  5. PILOT QUANTITY LEARNING


    • "Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

    • This procedure uses the GTS to perform "Pilot Quantity Learning".

    • When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).

    B007TH3E06

    Note

    After completing this procedure, clear the DTCs using the GTS.

    Tech Tips


    • B007SUQ

      If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

    • If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

    • If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

    • B007PS2

      A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot quantity learning.

    5. B007TGA

      Press "Next".

    6. B007RKQ

      Press "Next" again to proceed.

    7. B007S49

      Confirm that the atmospheric pressure screen is displayed.


      1. Confirm the displayed atmospheric pressure.

        Standard
        Atmosphere Pressure is 89 kPa or more

        Note


        • If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

        • If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.

      2. If the atmospheric pressure is within the standard range, proceed to the next screen.

    8. B007S6W

      Confirm the condition of the engine and wait until learning can be performed.

      Essential Conditions for Learning
      GTS Display Standard
      Coolant Temp 50 to 100°C
      Intake Air 10 to 120°C
      Fuel Temperature 25 to 96°C
      Battery Voltage 10 V or higher
      Reju Pilot Quantity Learning READY

      Tech Tips


      • If the values deviate from the standard above, "Pilot Quantity Learning" enters a standby state or is canceled.

      • When the essential conditions to perform learning are met, the screen will change automatically.

      Note


      • Using the GTS, make sure that DTCs other than DTC P1601 are not output.

      • If DTCs other than DTC P1601 are output, perform troubleshooting for those DTCs.

      Tech Tips

      DTC P1601 is stored when the value registered in the ECM for an input injector compensation code and/or pilot quantity deterioration learning value is the initial value.

    9. Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.

      B007SEH

      Tech Tips


      • After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

      • It is possible to confirm the status of the learning operation during "Pilot Quantity Learning" by observing the blinking pattern of the glow indicator light.

      Glow Indicator Light Blinking Pattern
      Learning Status Glow Indicator Light Condition
      Conditions essential to start learning have not been met Blinking at 0.5 second intervals
      Conditions essential to start learning have been met Blinking at 1 second intervals
      During racing (learning is being performed) Blinking at 1 second intervals
      Learning is finished Off
      Learning has been canceled Blinking at 1.5 second intervals
      Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)
      B007OT0E04
      B007T0XE05
    10. B007P6H

      When the screen changes, push "Exit".

    11. Turn the ignition switch off, and then turn the GTS off.

    12. Wait for at least 10 seconds.

    13. Turn the ignition switch to ON, and then turn the GTS on.

    14. Clear the DTCs Click here.

    15. Turn the ignition switch off.

      Note

      Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.

      Tech Tips


      • The main relay turns off after the learned value is stored in the ECM.

      • The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.

  6. PILOT QUANTITY LEARNING (DETAIL)


    • "Pilot Quantity Learning" is performed when injector assemblies have been replaced and injector compensation codes have been registered. "Pilot Quantity Learning (Detail)" is performed when there are engine problems but no DTCs are output and the technician wishes to clear the learned values and have the vehicle relearn the values.

      It takes time to clear the learned values and perform learning for all cylinders.

    • This procedure uses the GTS to perform "Pilot Quantity Learning (Detail)".

    • When replacing the injector assembly, engine or ECM, perform this procedure after performing injector compensation (manual ID code registration).

    B007TH3E07

    Note

    After completing this procedure, clear the DTCs using the GTS.

    Tech Tips


    • B007OG0

      If "Exit" is pushed during the step where the accelerator pedal is operated and "Pilot Quantity Learning (Detail)" is canceled, turn the ignition switch off, wait 10 seconds, check the vehicle condition, and then perform learning again.

    • If an error occurs during learning, check the vehicle condition after turning the ignition switch off, and then perform learning again.

    • If learning is canceled and DTCs are output due to excessive racing of the engine (depressing the accelerator pedal for 2 seconds or more), turn the ignition switch off, and then perform learning again.

    • B007RA4

      A communication malfunction may occur if there is a problem with the ECM, a wire harness or the connection to the DLC3. If the wire harnesses and the connection to the DLC3 are inspected and found to be normal, the ECM may be malfunctioning.


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot quantity learning (Detail).

    5. B007S5W

      Press "Next".

    6. B007PFT

      Press "Next" again to proceed.

    7. B007QKC

      Confirm that the atmospheric pressure screen is displayed.


      1. Confirm the displayed atmospheric pressure.

        Standard
        Atmosphere Pressure is 89 kPa or more

        Note


        • If the atmospheric pressure is below the standard range, "Pilot Quantity Learning" cannot be performed. In this case, press "Exit" and clear the learned values using "Pilot Quantity Learning Value Clear".

        • If the atmospheric pressure is below the standard range, even if "Pilot Quantity Learning" is performed, learning will not be completed.

      2. If the atmospheric pressure is within the standard range, proceed to the next screen.

    8. B007WF6

      Confirm the condition of the engine and wait until learning can be performed.

      Essential Conditions for Learning
      GTS Display Standard
      Coolant Temp 50 to 100°C
      Intake Air 10 to 120°C
      Fuel Temperature 25 to 96°C
      Battery Voltage 10 V or higher
      Reju Pilot Quantity Learning READY

      Tech Tips


      • If the values deviate from the standard above, "Pilot Quantity Learning (Detail)" enters a standby state or is canceled.

      • When the essential conditions to perform learning are met, the screen will change automatically.

      Note


      • Using the GTS, make sure that DTCs other than DTC P1601 are not output.

      • If DTCs other than DTC P1601 are output, perform troubleshooting for those DTCs.

      Tech Tips

      DTC P1601 is stored when the value registered in the ECM for an input injector compensation code and/or pilot quantity deterioration learning value is the initial value.

    9. Follow the prompts on the screen and repeat the following procedure until the screen changes: Starting with the engine idling, race the engine until the engine speed is 3000 rpm or more for no more than 2 seconds, and then let the engine return to idling.

      B007SEH

      Tech Tips


      • After confirming that the engine speed has reached 3000 rpm, completely release the accelerator pedal in order for the throttle opening amount to become 0%.

      • It is possible to confirm the status of the learning operation during "Pilot Quantity Learning (Detail)" by observing the blinking pattern of the glow indicator light.

      Glow Indicator Light Blinking Pattern
      Learning Status Glow Indicator Light Condition
      Conditions essential to start learning have not been met Blinking at 0.5 second intervals
      Conditions essential to start learning have been met Blinking at 1 second intervals
      During racing (learning is being performed) Blinking at 1 second intervals
      Learning is finished Off
      Learning has been canceled Blinking at 1.5 second intervals
      Learning has been canceled (malfunctioning cylinder is indicated by blinking pattern) Blinking at 0.8 second intervals (2.3 second intervals between each set of blinks representing the number of a malfunctioning cylinder)
      B007OT0E04
      B007T0XE05
    10. B007QO8

      When the screen changes, push "Exit".

    11. Turn the ignition switch off, and then turn the GTS off.

    12. Wait for at least 10 seconds.

    13. Turn the ignition switch to ON, and then turn the GTS on.

    14. Clear the DTCs Click here.

    15. Turn the ignition switch off.

      Note

      Do not disconnect the cable from the negative (-) battery terminal for 30 seconds after turning the ignition switch off.

      Tech Tips


      • The main relay turns off after the learned value is stored in the ECM.

      • The main relay turns off within approximately 5 to 10 seconds of turning the ignition switch off.

  7. PILOT QUANTITY LEARNING VALUE CLEAR

    Tech Tips


    • If the atmospheric pressure is below the threshold value, "Pilot Quantity Learning" will not be completed and DTC P1601 is stored. After "Pilot Quantity Learning Value Clear" is performed, DTC P1601 will not be stored.

    • Clear the learned values using the following procedure.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON, and then turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Utility / Pilot Quantity Learning Value Clear

    4. B007SUV

      Press "Next".

    5. B007Q3W

      Confirm that the atmospheric pressure screen is displayed.


      1. Confirm the displayed atmospheric pressure.

        Standard
        Atmosphere Pressure is below 89 kPa

        Note


        • If the atmospheric pressure is higher than the standard range for performing "Pilot Quantity Learning Value Clear", do not clear the learned values. Instead, perform "Pilot Quantity Learning".

        • When the atmospheric pressure is higher than the standard range, perform "Pilot Quantity Learning" without initializing the learned values using "Pilot Quantity Learning Value Clear". If the learned values are initialized when the atmospheric pressure is higher than the standard range, the following symptoms may appear. Be sure to correctly follow procedures.


          • Driveability problems

          • Rough idle

          • Emission of white or black smoke, etc.

      2. Proceed to the next screen.

    6. B007T30

      Select the cylinders whose learned value will be cleared.

      Note


      • Multiple cylinders can be selected.

      • Only the cylinders for which fuel injector compensation codes have been written must have their learned value cleared.

    7. After selecting the cylinders whose learned value will be cleared, press "Next" to begin the initialization.

    8. B007SOR

      When the screen changes, push "Exit".

    9. Turn the ignition switch off, and then turn the GTS off.

    10. Wait for at least 10 seconds.

    11. Turn the ignition switch to ON, and then turn the GTS on.

    12. Clear the DTCs Click here.

    13. Turn the ignition switch off and leave the vehicle for 30 seconds or more.

    14. Turn the ignition switch to ON for 1 second.

    15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    16. Read the DTCs.

    17. Confirm that no DTCs are output.