DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Data List.
According to the display on the GTS, read the Data List.
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
Mirror Selection SW (L) | Mirror select switch signal for LH mirror / ON or OFF | ON: Mirror select switch in L position OFF: Mirror select switch off or in R position |
- |
Mirror Selection SW (R) | Mirror select switch signal for RH mirror / ON or OFF | ON: Mirror select switch in R position OFF: Mirror select switch off or in L position |
- |
Mirror Position SW (L) | Mirror adjust switch signal (Left) / ON or OFF | ON: Mirror adjust switch pressed left OFF: Mirror adjust switch not pressed left |
Check with the mirror select switch in the L or R position. |
Mirror Position SW (R) | Mirror adjust switch signal (Right) / ON or OFF | ON: Mirror adjust switch pressed right OFF: Mirror adjust switch not pressed right |
Check with the mirror select switch in the L or R position. |
Mirror Position SW (Up) | Mirror adjust switch signal (Up) / ON or OFF | ON: Mirror adjust switch pressed up OFF: Mirror adjust switch not pressed up |
Check with the mirror select switch in the L or R position. |
Mirror Position SW (Dwn) | Mirror adjust switch signal (Down) / ON or OFF | ON: Mirror adjust switch pressed down OFF: Mirror adjust switch not pressed down |
Check with the mirror select switch in the L or R position. |
Outer Mirror Fold SW* | Retractable outer mirror switch signal / ON or OFF | ON: Retractable outer mirror switch in retract position OFF: Retractable outer mirror switch not in retract position |
- |
Auto Mirror SW* | Retractable outer mirror switch signal / ON or OFF | ON: Retractable outer mirror switch in AUTO position OFF: Retractable outer mirror switch not in AUTO position |
- |
*: w/ Retract Mirror
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
Seat Memory Switch1*1 | Seat memory switch M1 signal / ON or OFF | ON: Seat memory switch M1 on OFF: Seat memory switch M1 off |
- |
Seat Memory Switch2*1 | Seat memory switch M2 signal / ON or OFF | ON: Seat memory switch M2 on OFF: Seat memory switch M2 off |
- |
Seat Memory Switch3*1 | Seat memory switch M3 signal / ON or OFF | ON: Seat memory switch M3 on OFF: Seat memory switch M3 off |
- |
Seat Memory Set SW*1 | Seat memory switch SET signal / ON or OFF | ON: Seat memory switch SET on OFF: Seat memory switch SET off |
- |
Mirror Memory No.1 | No. 1 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.2 | No. 2 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.3 | No. 3 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.4 | No. 4 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.5 | No. 5 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.6 | No. 6 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory(Rev) No.1 | Reverse shift-linked mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Vertical Sensor Vol | Vertical mirror position / MIN: 0, MAX: 4.98 V | Within range of 0 to 4.98 V | - |
Mirror Fold Detect*2 | Condition of retractable outer mirror / Normal or Error | Normal: Retractable outer mirror is normal Error: Retractable outer mirror is malfunction |
- |
*1: for LHD
*2: w/ Retract Mirror
Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
---|---|---|---|
Seat Memory Switch1*1 | Seat memory switch M1 signal / ON or OFF | ON: Seat memory switch M1 on OFF: Seat memory switch M1 off |
- |
Seat Memory Switch2*1 | Seat memory switch M2 signal / ON or OFF | ON: Seat memory switch M2 on OFF: Seat memory switch M2 off |
- |
Seat Memory Switch3*1 | Seat memory switch M3 signal / ON or OFF | ON: Seat memory switch M3 on OFF: Seat memory switch M3 off |
- |
Seat Memory Set SW*1 | Seat memory switch SET signal / ON or OFF | ON: Seat memory switch SET on OFF: Seat memory switch SET off |
- |
Mirror Memory No.1 | No. 1 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.2 | No. 2 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.3 | No. 3 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.4 | No. 4 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.5 | No. 5 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory No.6 | No. 6 mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Memory(Rev) No.1 | Reverse shift-linked mirror position memorized / OFF or ON | ON: Memorized OFF: Not memorized |
- |
Mirror Vertical Sensor Vol | Vertical mirror position / MIN: 0, MAX: 4.98 V | Within range of 0 to 4.98 V | - |
Mirror Fold Detect*2 | Condition of retractable outer mirror / Normal or Error | Normal: Retractable outer mirror is normal Error: Retractable outer mirror is malfunction |
- |
*1: for RHD
*2: w/ Retract Mirror
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Active Test.
According to the display on the GTS, perform the Active Test.
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Mirror Up/Down | Mirror vertical operation | Up/Down | - |
Mirror Right/Left | Mirror horizontal operation | Right/Left | - |
Mirror Fold/Return*1 | Mirror retract operation | Fold/Return | - |
Mirror Heater*2 | Mirror heater operation | ON/OFF | - |
*1: w/ Retract Mirror
*2: w/ Mirror Heater
Tester Display | Test Part | Control Range | Diagnostic Note |
---|---|---|---|
Mirror Up/Down | Mirror vertical operation | Up/Down | - |
Mirror Right/Left | Mirror horizontal operation | Right/Left | - |
Mirror Fold/Return*1 | Mirror retract operation | Fold/Return | - |
Mirror Heater*2 | Mirror heater operation | ON/OFF | - |
*1: w/ Retract Mirror
*2: w/ Mirror Heater