Tech Tips
Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
PRECAUTION
Note
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the 3 clips and remove the front door lower frame bracket garnish.
REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect each connector and remove the multiplex network master switch assembly with front door armrest base panel.
REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.
Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.
REMOVE FRONT ARMREST ASSEMBLY
Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.
REMOVE COURTESY LIGHT ASSEMBLY
*A | for LH Side |
*B | for RH Side |
*1 | Protective Tape |
Using a screwdriver with its tip wrapped with protective tape, disengage the claw.
Disconnect the connector and remove the courtesy light assembly.
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
*1 | Protective Tape |
Put protective tape around the front door panel.
Remove the 3 screws.
Using a clip remover, disengage the 10 clips.
*1 | Reference Boss |
*2 | Front Door Inner Glass Weatherstrip |
Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.
Disengage the reference boss from the front door panel.
Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.
w/o Memory:
Disconnect the connector.
w/ Memory:
Disconnect the 2 connectors.
Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.
REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
*1 | Screwdriver |
Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.
REMOVE FRONT DOOR SERVICE HOLE COVER
Disconnect each connector.
Disengage the 4 clamps.
Remove the front door service hole cover.
Tech Tips
Remove any remaining butyl tape from the door.
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the grommet.
Connect the cable to the negative (-) battery terminal.
Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
Disconnect the multiplex network master switch assembly.
Remove the 2 bolts.
Note
After the bolts are removed, do not allow the door glass to fall.
Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.
Note
Do not damage the door glass.
REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
*1 | Temporary Bolt |
Loosen the temporary bolt.
Note
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.
Remove the 5 bolts.
Remove the front door window regulator assembly.
Remove the temporary bolt from the front door window regulator assembly.
REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.