DTC Code | DTC Name |
---|---|
P0351 | Ignition Coil "A" Primary / Secondary Circuit |
P0352 | Ignition Coil "B" Primary / Secondary Circuit |
P0353 | Ignition Coil "C" Primary / Secondary Circuit |
P0354 | Ignition Coil "D" Primary / Secondary Circuit |
DESCRIPTION
A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.
DTC No. | DTC Detection Condition | Trouble Area |
---|---|---|
P0351 P0352 P0353 P0354 |
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic). |
|
Reference: Inspection using an oscilloscope.
Items | Contents |
Terminals | 1. IGT1, IGT2, IGT3, IGT4 - E1 2. IGF1 - E1 |
Equipment Settings | 2 V/DIV, 20 msec./DIV |
Conditions | Idling |
Tech Tips
While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.
MONITOR DESCRIPTION
If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.
MONITOR STRATEGY
Required Sensors/Components (Main) | Igniter |
Required Sensors/Components (Related) | ECM |
Frequency of Operation | Continuous |
CONFIRMATION DRIVING PATTERN
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Idle the engine for 20 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
Tech Tips
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0351, P0352, P0353 or P0354.
Check the DTC judgment result.
GTS Display | Description |
---|---|
NORMAL |
|
ABNORMAL |
|
INCOMPLETE |
|
N/A |
|
Tech Tips
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
WIRING DIAGRAM
INSPECTION PROCEDURE
Tech Tips
These DTCs indicate malfunctions relating to the primary circuit.
If DTC P0351 is stored, check the No. 1 ignition coil circuit.
If DTC P0352 is stored, check the No. 2 ignition coil circuit.
If DTC P0353 is stored, check the No. 3 ignition coil circuit.
If DTC P0354 is stored, check the No. 4 ignition coil circuit.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
CHECK DTC OUTPUT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
Result | Proceed to |
---|---|
DTC P0351, P0352, P0353 or P0354 is output | A |
DTC P0351, P0352, P0353 and P0354 are output | B |
B |
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND) Click here |
A |
CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs Click here.
Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).
Note
Do not shuffle the connectors.
Perform a simulation test.
Check the DTCs output to the GTS.
Result | Proceed to |
---|---|
Same DTC output | A |
Different ignition coil assembly DTC output | B |
Tech Tips
Perform "Inspection After Repair" after replacing the ignition coil Click here.
B |
REPLACE IGNITION COIL ASSEMBLY |
A |
CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)
*a | Front view of wire harness connector (to Ignition Coil Assembly) |
Disconnect the ignition coil assembly connectors.
Measure the voltage according to the value(s) in the table below.
Standard Voltage | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
NG |
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND) Click here |
OK |
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
OK |
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
Disconnect the ignition coil assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
OK |
REPLACE ECM Click here
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
Disconnect the ignition coil assembly connectors.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND) |
OK |
CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - NO. 1 INTEGRATION RELAY)
Disconnect the ignition coil assembly connectors.
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
INSPECT NO. 1 INTEGRATION RELAY (INJ)
Inspect the No. 1 integration relay (INJ) Click here.
NG |
REPLACE NO. 1 INTEGRATION RELAY |
OK |
CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE)
*a | Front view of wire harness connector (to No. 1 Integration Relay) |
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard Voltage | ||||||
---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY) |
OK |
CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | ||||||
---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - NO. 1 INTEGRATION RELAY)
Remove the No. 1 integration relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
CHECK ECM POWER SOURCE CIRCUIT Click here