DTC Code | DTC Name |
---|---|
B27A2 | Open in Front Passenger Side Electrical Antenna Circuit |
DESCRIPTION
The certification ECU (smart key ECU assembly) generates a request signal and sends it to the door electrical key oscillator built into the front door outside handle assembly (for front passenger side) at 0.25-second intervals. To detect a key near the front passenger door, the front door outside handle assembly (for front passenger side) creates a detection area with a radius of approximately 1.0 m (3.28 ft.) from the front passenger door at 0.25-second intervals.
DTC B27A2 is detected by the certification ECU (smart key ECU assembly) if an open circuit is detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger side) terminals (between CLG2 and ANT1, or CG2B and ANT2).
DTC No. | DTC Detection Condition | Trouble Area |
---|---|---|
B27A2 | Open circuit detected between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger side) terminals (between CLG2 and ANT1, or CG2B and ANT2). |
|
INSPECTION PROCEDURE
The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.
PROCEDURE
CHECK CONNECTOR CONNECTION CONDITION
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and the front door outside handle assembly (for front passenger side).
OK |
---|
Connectors are properly connected. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the front door outside handle assembly (for front passenger side) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
|||||||||||||||||||||
|
*1 | Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
*2 | Front view of wire harness connector (to Front Door Outside Handle Assembly (for Front Passenger Side)) |
*3 | for LHD |
*4 | for RHD |
CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - BODY GROUND)
Measure the resistance according to the value(s) in the table below.
Standard Resistance | ||||||
---|---|---|---|---|---|---|
|
||||||
|
*1 | Front view of wire harness connector (to Front Door Outside Handle Assembly (for Front Passenger Side)) |
*2 | for LHD |
*3 | for RHD |
INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (DOOR ELECTRICAL KEY OSCILLATOR SIGNAL OUTPUT)
Reconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance and check for pulses according to the value(s) in the table below.
Standard Resistance | ||||||
---|---|---|---|---|---|---|
|
Standard | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
*1 | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Front Passenger Side)
Replace the front door outside handle assembly (for front passenger side) (Click here).
CHECK DTC OUTPUT
Clear the DTCs (Click here).
Recheck for DTCs.
OK |
---|
DTC B27A2 is not output. |
END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
REPAIR OR REPLACE HARNESS OR CONNECTOR
CONNECT CONNECTORS PROPERLY