AUDIO AND VISUAL SYSTEM(for Radio and Display Type) USB Audio System Recognition/Play Error

DTC Code DTC Name
USB Audio System Recognition/Play Error

DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

Figure 1. for LHD
E231119E07
Figure 2. for RHD
E231119E08

CAUTION / NOTICE / HINT

Tip:

  • When a large amount of data is in a USB device, it may take a while to begin play.

  • When using a USB device, files that are protected by copyright cannot be played.

  • When files are not played in the sorted order, perform the following procedure before inspection.

    1. Add numbers in front of the file names.

    2. Put the files in a folder and copy the folder data to the USB device.

PROCEDURE

  1. CHECK USB DEVICE OR "iPod"

    1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

    2. Check if playable files are present on the USB device or "iPod".

      Tip:

      Refer to System Description for playable files.

      Click hereClick here

    3. Check if the USB device is a compatible format or "iPod" is a compatible version.

      Tip:

      Refer to System Description for compatible formats and versions.

      Click hereClick here

    Result

    Result

    Proceed to

    No playable files exist, or incompatible device format or version

    A

    Playable files exist, and compatible device format or version

    B
    A

    USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

    B

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)

    1. Disconnect the G190*1 or G150*2 radio and display receiver assembly connector.

      • *1: for LHD

      • *2: for RHD

    2. Disconnect the G145 No. 1 stereo jack adapter assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Table 1. for LHD

      Tester Connection

      Condition

      Specified Condition

      G145-1 (UPI) - G190-1 (USV1)

      Always

      Below 1 Ω

      G145-2 (UDO-) - G190-2 (US1-)

      Always

      Below 1 Ω

      G145-3 (UDO+) - G190-3 (US1+)

      Always

      Below 1 Ω

      G145-4 (UJSG) - G190-4 (UGD1)

      Always

      Below 1 Ω

      G145-1 (UPI) - Body ground

      Always

      10 kΩ or higher

      G145-2 (UDO-) - Body ground

      Always

      10 kΩ or higher

      G145-3 (UDO+) - Body ground

      Always

      10 kΩ or higher

      G145-4 (UJSG) - Body ground

      Always

      10 kΩ or higher
      Table 2. for RHD

      Tester Connection

      Condition

      Specified Condition

      G145-1 (UPI) - G150-1 (UPO)

      Always

      Below 1 Ω

      G145-2 (UDO-) - G150-2 (UDO-)

      Always

      Below 1 Ω

      G145-3 (UDO+) - G150-3 (UDO+)

      Always

      Below 1 Ω

      G145-4 (UJSG) - G150-4 (UESG)

      Always

      Below 1 Ω

      G145-1 (UPI) - Body ground

      Always

      10 kΩ or higher

      G145-2 (UDO-) - Body ground

      Always

      10 kΩ or higher

      G145-3 (UDO+) - Body ground

      Always

      10 kΩ or higher

      G145-4 (UJSG) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

    1. Disconnect the No. 1 stereo jack adapter assembly connector.

    2. E193009C02

      *a

      Front view of wire harness connector

      (to No. 1 Stereo Jack Adapter Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      G145-1 (UPI) - G145-4 (UJSG)

      Ignition switch ACC

      4.5 to 5.5 V

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    Click here

    OK

  4. FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK

    1. Delete all files in the USB device or "iPod" and format/restore it.

    2. Save the data again and check if it can be played on the in-vehicle device.

      Note:

      Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.

    Result

    Proceed to

    Malfunction disappears

    Malfunction appears
    Malfunction disappears

    END

    Malfunction appears

  5. CHECK USB DEVICE OR "iPod"

    1. Turn the ignition switch off.

      Tip:

      When this malfunction occurs, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.

    2. Turn the ignition switch to ACC.

    3. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

      Tip:

      • If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.

      • Refer to System Description for compatible formats and versions.

        Click hereClick here

    4. Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album name, is displayed on the screen.

    Result

    Proceed to

    Malfunction disappears

    Malfunction appears
    Malfunction disappears

    USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE

    Malfunction appears

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click hereClick here