MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
*A |
w/ Stop and Start System |
*B |
w/o Stop and Start System |
*1 |
CONTROL CABLE BRACKET ASSEMBLY |
*2 |
MANUAL TRANSMISSION DRAIN PLUG |
*3 |
MANUAL TRANSMISSION FILLER PLUG |
*4 |
NEUTRAL POSITION SWITCH |
*5 |
NO. 1 CLUTCH HOUSING COVER |
*6 |
RELEASE CYLINDER BLEEDER PLUG |
*7 |
RELEASE CYLINDER BLEEDER PLUG CAP |
*8 |
TRANSMISSION CASE PLUG |
*9 |
WIRE HARNESS CLAMP BRACKET |
*10 |
CLUTCH RELEASE CYLINDER TO BLEEDER TUBE |
*11 |
CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
*12 |
BACK-UP LIGHT SWITCH ASSEMBLY |
*13 |
CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
*14 |
BREATHER PLUG |
*15 |
CLUTCH TUBE BOOT |
*16 |
GASKET |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
Clutch spline grease |
- |
- |
ILLUSTRATION
*1 |
STRAIGHT PIN |
*2 |
PLUG |
*3 |
SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING |
*4 |
LOCK BALL PIN |
*5 |
TRANSMISSION CASE PLUG |
*6 |
REVERSE IDLER GEAR SHAFT BOLT |
*7 |
SHIFT DETENT BALL |
*8 |
SHIFT DETENT BALL COMPRESSION SPRING |
*9 |
SHIFT DETENT BALL PLUG |
*10 |
NO. 1 LOCK BALL ASSEMBLY |
*11 |
OUTER SHIFT LEVER E-RING |
*12 |
GASKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
Adhesive 1344 |
 |
Adhesive 1324 |
★ |
Precoated part |
- |
- |
ILLUSTRATION
*1 |
OUTER SELECT LEVER |
*2 |
OUTER SELECT LEVER OIL SEAL |
*3 |
INNER SELECT LEVER |
*4 |
INNER SELECT LEVER SET BOLT |
*5 |
REVERSE SHIFT ARM BRACKET ASSEMBLY |
*6 |
REVERSE SHIFT FORK SHAFT ASSEMBLY |
*7 |
REVERSE IDLER GEAR SUB-ASSEMBLY |
*8 |
REVERSE IDLER THRUST WASHER |
*9 |
REVERSE IDLER GEAR SHAFT |
*10 |
INPUT SHAFT ASSEMBLY |
*11 |
NO. 3 GEAR SHIFT FORK SHAFT ASSEMBLY |
*12 |
NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
*13 |
NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY |
*14 |
OUTPUT SHAFT ASSEMBLY |
*15 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (INNER RACE) |
*16 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (INNER RACE) |
*17 |
SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
*18 |
SHIFT INTER LOCK PLATE |
*19 |
DIFFERENTIAL CASE ASSEMBLY |
*20 |
SLOTTED SPRING PIN |
*21 |
REVERSE SHIFT FORK |
*22 |
NO. 4 GEAR SHIFT FORK SHAFT |
*23 |
NO. 1 GEAR SHIFT HEAD |
*24 |
NO. 1 GEAR SHIFT FORK ASSEMBLY |
*25 |
NO. 3 GEAR SHIFT HEAD |
*26 |
NO. 3 REVERSE PRE-BALK HEAD |
*27 |
NO. 3 GEAR SHIFT FORK ASSEMBLY |
*28 |
NO. 2 GEAR SHIFT HEAD |
*29 |
SNAP RING |
*30 |
SPACER |
*31 |
NO. 2 REVERSE PRE-BALK HEAD |
*32 |
STRAIGHT PIN |
*33 |
BIMETAL FORMED BUSHING |
*34 |
TORSION SPRING |
*35 |
SHIFT LEVER STOPPER |
*36 |
NO. 2 GEAR SHIFT FORK ASSEMBLY |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
|
Adhesive 1324 |
★ |
Precoated part |
- |
- |
ILLUSTRATION
*1 |
TRANSAXLE CASE OIL SEAL |
*2 |
FRONT OUTPUT SHAFT BEARING (OUTER RACE) |
*3 |
FRONT TRANSAXLE CASE OIL SEAL |
*4 |
REVERSE RESTRICT PIN ASSEMBLY |
*5 |
TRANSMISSION MAGNET |
*6 |
TRANSMISSION OIL SEPARATOR |
*7 |
OUTPUT SHAFT COVER |
*8 |
FRONT DIFFERENTIAL CASE FRONT PLATE WASHER |
*9 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING (OUTER RACE) |
*10 |
FRONT TRANSAXLE CASE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |
ILLUSTRATION
*1 |
TRANSMISSION CASE OIL SEAL |
*2 |
INPUT SHAFT COVER |
*3 |
MANUAL TRANSMISSION CASE |
*4 |
MANUAL TRANSMISSION OIL SEPARATOR SUB-ASSEMBLY |
*5 |
NO. 1 OIL RECEIVER PIPE |
*6 |
OUTER NO. 1 SHIFT LEVER |
*7 |
OUTER SHIFT LEVER OIL SEAL |
*8 |
REAR INPUT SHAFT BEARING SHIM |
*9 |
REAR OUTPUT SHAFT BEARING (OUTER RACE) |
*10 |
TRANSMISSION OIL SEPARATOR |
*11 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING (OUTER RACE) |
*12 |
REAR OUTPUT SHAFT BEARING SHIM |
*13 |
FRONT DIFFERENTIAL CASE REAR PLATE WASHER |
*14 |
OUTER SHIFT LEVER SPACER |
*15 |
INNER NO. 1 SHIFT LEVER |
*16 |
INNER SHIFT LEVER SLOTTED SPRING PIN |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
- |
- |