CRUISE CONTROL SYSTEM Cruise Control Switch Circuit

DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the hybrid vehicle control ECU reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

B005YO7E47

PROCEDURE


  1. READ VALUE ON GTS

    B005YF2E35
    Text in Illustration
    *a ON-OFF
    *b -/SET
    *c +/RES
    *d CANCEL

    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Select the following menu items: Powertrain / Cruise Control / Data List.

    5. Check the Data List to confirm proper functioning of the cruise control switch.

      Cruise Control
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Cancel Switch CANCEL switch status ON or OFF

      ON: CANCEL switch on

      OFF: CANCEL switch off

      		 -
      -SET Switch -SET switch status ON or OFF

      ON: -SET switch on

      OFF: -SET switch off

      		 -
      +RES Switch +RES switch status ON or OFF

      ON: +RES switch on

      OFF: +RES switch off

      		 -
      Cruise Main Switch Operation Condition Cruise control main switch (ON-OFF button) status ON or OFF

      ON: Cruise control main switch pushed

      OFF: Cruise control main switch not pushed

      		 -
      OK
      When the cruise control switch is operated, the display changes as shown above.

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. INSPECT CRUISE CONTROL SWITCH


    1. Remove the cruise control switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      B005XM1E01
      Text in Illustration
      *1 Cruise Control Switch (ON-OFF button) - -
      *a

      Component without harness connected

      (Cruise Control Switch)

      		 *b ON-OFF
      *c +/RES *d -/SET
      *e CANCEL - -
      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 3 Cruise control switch (ON-OFF button) released 1 MΩ or higher
      Cruise control switch (ON-OFF button) pushed Below 2.5 Ω
      +/RES 235 to 245 Ω
      -/SET 617 to 643 Ω
      CANCEL 1509 to 1571 Ω

    NG

    REPLACE CRUISE CONTROL SWITCH Click here

    OK

  3. CHECK CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)


    1. B005Z4BE02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly)
      *b

      Front view of wire harness connector

      (to Cruise Control Switch)

      Disconnect the spiral with sensor cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Specified Condition
      z10-3 - 3 Below 2.5 Ω
      z10-4 - 1 Below 2.5 Ω

    NG

    REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE (SPIRAL CABLE SUB-ASSEMBLY - CRUISE CONTROL SWITCH)

    OK

  4. CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

    Note

    The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    Tech Tips



    1. Remove the spiral with sensor cable sub-assembly.

      B005YYSE01

    2. Measure the resistance according to the value(s) in the table below.

    3. After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      z10-3 - L52-1 (CCS) Always Below 1 Ω
      z10-4 - L52-2 (ECC) Always Below 1 Ω
      Text in Illustration
      *a

      Component without harness connected

      (Spiral with Sensor Cable Sub-assembly)

      Tech Tips

      The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.


    NG

    REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - SPIRAL CABLE SUB-ASSEMBLY)


    1. Disconnect the hybrid vehicle control ECU connector.

    2. Disconnect the spiral with sensor cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      L52-1 (CCS) - L5-28 (CCS) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      L52-1 (CCS) or L5-28 (CCS) - Body ground Always 10 kΩ or higher

    4. Reconnect the spiral with sensor cable sub-assembly connector.

    5. Reconnect the hybrid vehicle control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)

    OK

  6. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)


    1. B005XX0E02
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly)

      Disconnect the spiral with sensor cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      L52-2 (ECC) - Body ground Always Below 1 Ω

    3. Reconnect the spiral with sensor cable sub-assembly connector.


    OK

    REPLACE HYBRID VEHICLE CONTROL ECU Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)