AIRBAG SYSTEM SRS Warning Light Remains ON

DTC Code DTC Name
SRS Warning Light Remains ON

DESCRIPTION

The SRS warning light is located in the combination meter.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the engine switch is turned from off to on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor to the combination meter through the CAN communication system.

WIRING DIAGRAM

C175154E14

CAUTION / NOTICE / HINT

Note:

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

PROCEDURE

  1. CHECK CAN COMMUNICATION SYSTEM

    1. Check if a CAN communication DTC is output.

      Click here

      Result

      Result

      Proceed to

      DTC is not output

      A

      DTCs are output

      B
    B

    REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

    Click here

    A

  2. CHECK BATTERY

    1. Measure the voltage of the battery.

      Standard voltage

      11 to 14 V

      Result

      Result

      OK

      NG
    NG

    REPLACE OR RECHARGE BATTERY

    OK

  3. CHECK CONNECTORS

    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor and combination meter.

      OK

      The connectors are properly connected.

      Result

      Result

      OK

      NG
    NG

    CONNECT CONNECTORS PROPERLY

    OK

  4. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

    1. C198548C02

      *a

      Rear view of wire harness connector

      (to Center Airbag Sensor)

      Disconnect the connectors from the center airbag sensor.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the engine switch on (IG).

    4. Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      G1-21 (IG2) - G1-25 (E1)

      Engine switch on (IG)

      11 to 14 V

      G1-21 (IG2) - G1-26 (E2)

      Engine switch on (IG)

      11 to 14 V

      Result

      Result

      OK

      NG
    NG

    REPLACE INSTRUMENT PANEL WIRE

    OK

  5. CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

    1. C198549C03

      *a

      Front view of wire harness connector

      (to Combination Meter)

      Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    2. Disconnect the G3 connector from the combination meter.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Switch Condition

      Specified Condition

      G3-27 (IG+) - G3-21 (E2)

      Engine switch on (IG)

      11 to 14 V

      G3-25 (B) - G3-21 (E2)

      Engine switch on (IG)

      11 to 14 V

      Result

      Result

      OK

      NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK SRS WARNING LIGHT (SHORT TO GROUND)

    1. Turn the engine switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Connect the connector to the combination meter.

    4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    5. Turn the engine switch on (IG).

    6. Check the SRS warning light condition.

      Note:

      Make sure that nobody is in the vehicle.

      OK

      After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.

      Tip:

      The primary check period is approximately 6 seconds after the engine switch is turned on (IG).

      Result

      Result

      OK

      NG
    OK

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY

    Click here

    NG

    GO TO METER / GAUGE SYSTEM

    Click here