TRANSMISSION CONTROL CABLE INSTALLATION

PROCEDURE

  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

    1. C296270

      Install the transmission control cable assembly to the body with the 2 bolts.

      5.0 N*m

      51 kgf*cm

      44 in.*lbf

    2. C316613

      Install the transmission control cable assembly to rear engine mounting insulator with the bolt.

      5.0 N*m

      51 kgf*cm

      44 in.*lbf

    3. C296306

      Install the transmission control cable assembly to the transmission control cable support with the nut.

      12 N*m

      122 kgf*cm

      9 ft.*lbf

    4. C300679C01

      *a

      P Position

      *b

      N Position

      Turn the control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.

    5. C296239

      Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

    6. Install the transmission control cable assembly to the control shaft lever with the nut.

      12 N*m

      122 kgf*cm

      9 ft.*lbf

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

    1. Turn the nut of the transmission control cable 180° counterclockwise. While holding the nut in place, push in the stopper to lock the nut.

      C328348C01

      *1

      Stopper

      *2

      Nut
      V113147

      Turn in this Direction

      		 V113148

      Push in this Direction
      Note:

      Do not over-rotate the nut as it will come off the internal spring and the transmission control cable will not be reusable.

      Tip:

      If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.

    2. Install the outer part of the transmission control cable assembly to the shift lever assembly. Check that the stopper returns to the pulled out position.

      C328349C01

      *1

      Stopper

      *2

      Nut

      *3

      Shift Lever Assembly

      -

      -
      V113147

      Install in this Direction

      -

      -
    3. C328343C02

      *1

      Slider

      *2

      Lock Piece
      V113147

      Slide in this Direction
      V113148

      Pull in this Direction

      Slide the slider in the direction shown in the illustration and pull out the lock piece.

    4. C328345C01
      V113147

      Connect in this Direction

      Connect the end of the transmission control cable assembly to the shift lever assembly.

      Note:

      • Make sure that the lock piece is pulled up.

      • Push on the end of the transmission control cable assembly all the way to the base of the pin.

    5. C328344C02

      *1

      Cable Rod
      V113147

      Push in this Direction

      Gently pull the cable rod toward the rear of the vehicle by hand to pull the cable taut.

    6. Push the lock piece into the adjuster case and lock it.

      Note:

      Make sure that the lock piece is completely locked by the slider.

  3. INSPECT SHIFT LEVER POSITION

    Click here

  4. ADJUST SHIFT LEVER POSITION

    Click here

  5. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  6. INSTALL FRONT FLOOR COVER

    Click here

  7. INSTALL BATTERY BRACKET REINFORCEMENT

    Click here

  8. INSTALL FRONT BATTERY BRACKET

    Click here

  9. CONNECT RADIATOR HOSE SUB-ASSEMBLY

    Click here

  10. INSTALL BATTERY TRAY

  11. INSTALL BATTERY

  12. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

  13. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  14. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

    1. Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.

  15. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  16. INSTALL NO. 2 CYLINDER HEAD COVER

    Click here

  17. CONNECT CABLE TO POSITIVE BATTERY TERMINAL

  18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here