ULTRASONIC SENSOR(for Front) INSTALLATION

PROCEDURE


  1. INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER


    1. A001UQ5C01
      B008LJK Install in this Direction

      Engage the claws to install the front center ultrasonic sensor retainer as shown in illustration.

  2. INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

    • If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.


    1. Clean the surface of the front bumper cover.


      1. Remove any remaining double-sided tape from the front bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    2. A001SK9C01
      *a 18.4 to 18.8 mm (0.724 to 0.7401 in.)

      Cover the sensor installation hole with a 18.4 to 18.8 mm (0.724 to 0.7401 in.) circular piece of tape.

    3. Using a brush or felt, apply primer or equivalent to the 2 front corner ultrasonic sensor retainers installation area.

      A001TVFC01
      *a Line - -
      A001WOT Primer - -

      Note


      • Use a clean brush or felt.

      • Do not touch the front bumper assembly until the primer has dried.

    4. Peel off the release paper from the 2 front corner ultrasonic sensor retainers.

    5. Align the front corner ultrasonic sensor retainer with the mark on the front bumper cover and install it as shown in the illustration.

      Note

      The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new front corner ultrasonic sensor retainer when reattachment is necessary.

      A001V72C01
      *a Line - -
      B008MCV Press area - -

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper cover. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper cover.

  3. INSTALL FRONT SIDE ULTRASONIC SENSOR RETAINER (w/ Simple Intelligent Parking Assist System)

    Tech Tips


    • Perform this procedure only when replacement of the front side ultrasonic sensor retainer is necessary.

    • If a front side ultrasonic sensor retainer has been removed, replace it with a new one.

    • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. Clean the surface of the front bumper cover.


      1. Remove any remaining double-sided tape from the front bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    2. A001SK9C01
      *a 26.2 to 26.6 mm (1.031 to 1.047 in.)

      Cover the sensor installation hole with a 26.2 to 26.6 mm (1.031 to 1.047 in.) circular piece of tape.

    3. A001U8LC01
      *a Line
      A001WOT Primer

      Using a brush or felt, apply primer or equivalent to the front side ultrasonic sensor retainer installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the front bumper assembly until the primer has dried.

    4. Peel off the release paper from the front side ultrasonic sensor retainer.

    5. A001XX4C01
      *a Line
      B008MCV Press area

      Align the front side ultrasonic sensor retainer with the mark on the front bumper cover and install it as shown in the illustration.

      Note

      The double-sided tape of a front side ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new front side ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front side ultrasonic sensor retainer to the front bumper cover. Confirm there is no clearance between the front side ultrasonic sensor retainer and front bumper cover.

  4. INSTALL FRONT CENTER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A001X2ZC01
      B008LJK Install in this Direction

      Engage the claws to install the front center ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  5. INSTALL FRONT CORNER ULTRASONIC SENSOR

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A001YFQC01
      B008LJK Install in this Direction

      Engage the claws to install the front corner ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  6. INSTALL FRONT SIDE ULTRASONIC SENSOR (w/ Simple Intelligent Parking Assist System)

    Tech Tips

    The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


    1. A001XMCC01
      B008LJK Install in this Direction

      Engage the claws to install the front side ultrasonic sensor as shown in the illustration.

    2. Connect the connector.

  7. INSTALL FRONT BUMPER ASSEMBLY

    Click here