ROOF SUNSHADE SYSTEM, Diagnostic DTC:B2346

DTC Code DTC Name
B2346 Lost Communication with Front Shade Module

DESCRIPTION

This DTC is stored when LIN communication between the sliding roof drive gear sub-assembly (sliding roof ECU) and sliding roof drive gear assembly (front roof sunshade ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2346 Lost Communication with Front Shade Module No communication between the sliding roof drive gear sub-assembly (sliding roof ECU) and sliding roof drive gear assembly (front roof sunshade ECU) for 10 seconds or more.
  • Sliding roof drive gear sub-assembly (sliding roof ECU)

  • Sliding roof drive gear assembly (front roof sunshade ECU)

  • Harness or connector

WIRING DIAGRAM

B006DTYE01

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off to troubleshoot:

    Connect the GTS to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • When the sliding roof drive gear sub-assembly (sliding roof ECU) is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly (sliding roof ECU) must be initialized.

    Click here

  • When the sliding roof drive gear assembly (front roof sunshade ECU) is removed and reinstalled or replaced, the sliding roof drive gear assembly (front roof sunshade ECU) must be initialized.

    Click here

PROCEDURE


  1. CLEAR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Sliding Roof > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT
  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Sliding Roof > Trouble Codes
      Result
      Proceed to
      DTC B2346 is output
      DTC B2346 is not output

    DTC B2346 is not output
    DTC B2346 is output
  3. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY [SLIDING ROOF ECU] - SLIDING ROOF DRIVE GEAR ASSEMBLY [FRONT ROOF SUNSHADE ECU])


    1. Disconnect the N4 sliding roof drive gear sub-assembly (sliding roof ECU) connector.

    2. Disconnect the N32 sliding roof drive gear assembly (front roof sunshade ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N4-3 (MPX2) - N32-3 (MPX2) Always Below 1 Ω
      N4-3 (MPX2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG
    OK
  4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR ASSEMBLY [FRONT ROOF SUNSHADE ECU] - BATTERY AND BODY GROUND)


    1. Disconnect the N32 sliding roof drive gear assembly (front roof sunshade ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N32-2 (E) - Body ground Always Below 1 Ω
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      N32-1 (B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG
    OK
  5. CHECK SLIDING ROOF DRIVE GEAR ASSEMBLY (FRONT ROOF SUNSHADE ECU)


    1. Temporarily replace the sliding roof drive gear assembly (front roof sunshade ECU) with a new or normally functioning one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Sliding Roof > Clear DTCs
      Result
      Proceed to
      NEXT

    NEXT
  6. CHECK FOR DTC


    1. Check for DTCs.

      Click here


      Body Electrical > Sliding Roof > Trouble Codes
      Result
      Proceed to
      DTC B2346 is not output
      DTC B2346 is output

    DTC B2346 is not output
    DTC B2346 is output