PARKING ASSIST MONITOR SYSTEM(w/o Side Monitor System) DIAGNOSIS SYSTEM

  1. PARKING ASSIST MONITOR SYSTEM DIAGNOSTIC MODE

    1. In diagnostic mode for the parking assist monitor system, signals received by the multi-media module receiver assembly can be checked and the parking assist monitor system can be calibrated, adjusted and checked using the multi-display.

      Note:

      Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

      Click hereClick here

      Tip:

      The displayed items may differ depending on vehicle specifications.

  2. DIAGNOSIS SCREEN TRANSITION (DURING PARKING ASSIST MONITOR SYSTEM INITIALIZATION)

    E283800E01
    E276135

  3. DIAGNOSIS SCREEN TRANSITION (AFTER PARKING ASSIST MONITOR SYSTEM INITIALIZATION)

    E283801E01
    E276136

  4. VEHICLE SIGNAL CHECK (MULTI-MEDIA MODULE RECEIVER ASSEMBLY INPUT SIGNALS)

    Tip:

    Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    1. Start diagnostic mode.

      Click here

    2. E271944

      Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

    3. E271945

      Select "Vehicle Signal" on the "Function Check/Setting I" screen.

    4. E225776

      Vehicle Signal Check Mode

      1. When the "Vehicle Signal Check Mode" screen is displayed, check the item displayed for "REV".

        Click hereClick here

        Tip:

        • Only conditions having inputs are displayed.

        • This screen displays vehicle signals input to the multi-media module receiver assembly.

    5. Finish diagnostic mode.

      Click here

  5. Tip:

    Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

    CAR SIGNAL CHECK (PARKING ASSIST MONITOR SYSTEM INPUT SIGNALS)

    1. Start diagnostic mode.

      Click here

      1. E271944

        Select "Function Check/Setting" on the "Service Menu" screen to display the "Function Check/Setting I" screen.

      2. E271945

        Select "Camera Setting" on the "Function Check/Setting I" screen.

      3. E283802

        Select "Next" on the "Car Information Check" screen.

        Tip:

        After "Next" is selected, the screen transitions differ depending on whether initialization of the parking assist monitor system was performed after the multi-media module receiver assembly was replaced.

        Parking Assist Monitor System Initialization

        Screen Transition

        Not performed

        Car Signal Check screen

        Performed

        Mode Setting screen
      4. E276139

        When the screen changes to the "Mode Setting" screen, select "Back Camera Setting" to display the "Car Signal Check" screen.

        Tip:

        To select a grayed out item, select and hold the item for 2 seconds or more.

    2. E276130

      Car Signal Check

      1. On the "Car Signal Check" screen, it is possible to inspect the state of signals and check the settings.

        Item

        Inspection Detail

        Note

        BCTY

        Back door courtesy switch signal input

        When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
        Tip:

        • When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.

        • If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".

    3. BCTY inspection

      Tip:

      If "CHK" (red) is displayed for "BCTY", check for DTCs and perform troubleshooting based on the output DTCs.

      Click here

    4. Finish diagnostic mode.

      Click here

  6. CAMERA SYNCHRONOUS ERROR HISTORY

    Tip:

    This function is used to check the date and time of occurrence when a camera synchronous error occurs.

    1. Check camera synchronous error history.

      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Camera Synchronous Error History.

        Body Electrical > Navigation System > Utility

        Tester Display

        Camera Synchronous Error History

      5. When an item is stored for Camera Synchronous Error History, record it before repairing the multi-media module receiver assembly and rear television camera assembly.

        Tip:

        Camera Synchronous Error History can store up to 5 history data items. If a new camera synchronous error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

    2. Clear camera synchronous error history.

      1. When DTCs are cleared using any of the following operations, Camera Synchronous Error History will be cleared as well.

        Click here

        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  7. VIDEO DEVICE CONNECTION CHECK

    Click hereClick here

  8. CALIBRATION WHEN SERVICING VEHICLE

    Note:

    Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed.

    Click hereClick here