FRONT BUMPER REASSEMBLY

PROCEDURE

  1. INSTALL LOWER RADIATOR GRILLE MOULDING (w/ Plated Moulding)

    1. Attach the 9 claws to install the lower radiator grille moulding.

  2. INSTALL LOWER RADIATOR GRILLE MOULDING (w/ Plated Moulding)

    1. Attach the 9 claws to install the lower radiator grille moulding.

  3. INSTALL FRONT BUMPER HOLE COVER RH

    1. Attach the 3 claws to install the front bumper hole cover RH.

  4. INSTALL LOWER NO. 1 RADIATOR GRILLE

    1. Attach the 22 claws to install the lower No. 1 radiator grille.

  5. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM

    1. Attach the 2 claws and 2 guides to install the radiator grille (or front panel) emblem.

  6. INSTALL RADIATOR GRILLE

    1. Attach the 12 claws to install the radiator grille.

    2. Install the 2 screws.

  7. INSTALL CENTER RADIATOR GRILLE MOULDING LH

    1. Attach the claw to install the center radiator grille moulding LH.

  8. INSTALL CENTER RADIATOR GRILLE MOULDING RH

    Tip:

    Use the same procedure described for the LH side.

  9. INSTALL RADIATOR GRILLE SIDE MOULDING LH

    1. Attach the 9 claws to install the radiator grille side moulding LH.

  10. INSTALL RADIATOR GRILLE SIDE MOULDING RH

    Tip:

    Use the same procedure described for the LH side.

  11. INSTALL UPPER FRONT BUMPER RETAINER

    1. Install the upper front bumper retainer with the 4 clips.

  12. INSTALL FRONT HOOD TO END PANEL SEAL

    Tip:

    When installing the front hood to end panel seal, heat the front bumper surface using a heat light.

    Standard

    Item

    Temperature

    Front Bumper Cover

    20 to 30°C (68 to 86°F)
    Note:

    Do not heat the front bumper cover excessively.

    1. Clean the front bumper surface cover.

      1. Using a heat light, heat the front bumper cover surface.

      2. Remove the double-sided tape from the front bumper cover surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new front hood to end panel seal.

      1. Remove the peeling paper from the face of a new front hood to end panel seal.

        Tip:

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      2. Install the front hood to end panel seal.

    3. Install the 4 clips.

  13. INSTALL FOG LIGHT MOUNTING BRACKET LH (w/ Bracket)

    1. Attach the 4 claws to install the fog light mounting bracket LH.

  14. INSTALL FOG LIGHT MOUNTING BRACKET RH (w/ Bracket)

    Tip:

    Use the same procedure described for the LH side.

  15. INSTALL FOG LIGHT COVER LH

    1. Attach the 5 claws to install the fog light cover LH.

  16. INSTALL FOG LIGHT COVER RH

    Tip:

    Use the same procedure described for the LH side.

  17. INSTALL FOG LIGHT ASSEMBLY LH

    Click here

  18. INSTALL FOG LIGHT ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  19. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

    Click here

  20. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

    Tip:

    Use the same procedure described for the LH side.

  21. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

    Click here

  22. INSTALL HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

    Tip:

    Use the same procedure described for the LH side.

  23. INSTALL HEADLIGHT WASHER HOSE (w/ Headlight Cleaner System)

    Click here

  24. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

    Click here

  25. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here

  26. INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)

    Click here