VEHICLE STABILITY CONTROL SYSTEM VSC OFF Indicator Light does not Come ON

DESCRIPTION

Refer to VSC OFF Indicator Light Remains ON Click here.

WIRING DIAGRAM

Refer to VSC OFF Indicator Light Remains ON Click here.

INSPECTION PROCEDURE

Note


  • After replacing the brake actuator assembly, perform calibration Click here.

  • Before disconnecting the connector, make sure that there are no problems with the connection.

  • After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.

PROCEDURE


  1. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED


    1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

      OK
      The connector is securely connected.

    NG

    CONNECT CONNECTOR TO ECU CORRECTLY

    OK

  2. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)


    1. Turn the ignition switch off.

    2. Disconnect the skid control ECU (brake actuator assembly) connector.

    3. A01DW3AE58
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Skid Control ECU [Brake Actuator Assembly])

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      S35-34 (IG1) - Body ground Ignition switch ON 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    1. Turn the ignition switch off.

    2. Disconnect the skid control ECU (brake actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S35-1 (GND1) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT VSC OFF SWITCH


    1. Turn the ignition switch off.

    2. Remove the VSC OFF switch Click here.

    3. Inspect the VSC OFF switch Click here.


    NG

    REPLACE VSC OFF SWITCH Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


    1. Turn the ignition switch off.

    2. Disconnect the VSC OFF switch connector.

    3. Disconnect the skid control ECU (brake actuator assembly) connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S35-30 (CSW) - V8-3 Always Below 1 Ω
      S35-30 (CSW) - Body ground Always 10 kΩ or higher
      V8-4 - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)


    1. Turn the ignition switch off.

    2. Disconnect the skid control ECU (brake actuator assembly) connector.

    3. Disconnect the C26 combination meter connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S35-15 (VSCW) - C26-16 Always Below 1 Ω
      S35-15 (VSCW) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (VSC WARNING LIGHT)


    1. Turn the ignition switch off.

    2. Connect the intelligent tester to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the intelligent tester on.

    5. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

      ABS/VSC/TRC
      Tester Display Test Part Control Range Diagnostic Note
      VSC Warning Light VSC OFF indicator light Indicator light ON / OFF Observe the combination meter.

    6. When performing the VSC Warning Light Active Test, check VSC Warning Light in the Data List.

      ABS/VSC/TRC
      Tester Display Measurement Item / Range Normal Condition Diagnostic Note
      VSC Warning Light VSC OFF indicator light / ON or OFF

      ON: VSC OFF indicator light on

      OFF: VSC OFF indicator light off

      		 -
      Result
      Result Proceed to
      Data List Display Data List Display When Performing Active Test ON/OFF Operation
      ON Does not change between ON and OFF for LHD A
      Does not change between ON and OFF for RHD B
      Changes between ON and OFF C
      OFF Does not change between ON and OFF for LHD A
      Does not change between ON and OFF for RHD B
      Changes between ON and OFF C

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

    C

    GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    A

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here