SFI SYSTEM, Diagnostic DTC:P003373

DTC Code DTC Name
P003373 Turbocharger / Supercharger Bypass Valve "A" Control Actuator Stuck Closed

DESCRIPTION

Refer to DTC P003312.

Click hereClick here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P003373

Turbocharger / Supercharger Bypass Valve "A" Control Actuator Stuck Closed

The boost pressure does not drop despite control to open the air by-pass valve being commanded (1 trip detection logic).

  • Air by-pass valve (turbocharger sub-assembly)

  • No. 1 turbo pressure sensor

  • Wire harness or connector

  • ECM

Does not come on

DTC stored

SAE Code: P0039

MONITOR DESCRIPTION

If the throttle valve is closed while boost pressure is being applied, the air by-pass valve opens and the excess pressure between the turbocharger and the throttle valve is released. If the boost pressure does not drop for a certain amount of time despite control to open the air by-pass valve being commanded, the ECM determines that the air by-pass valve is stuck closed and stores this DTC.

CONFIRMATION DRIVING PATTERN

A330723E04

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on.

  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

  7. Accelerate to 50 km/h (31 mph) or more with the accelerator pedal fully depressed [B].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Quickly release the accelerator pedal from the fully depressed position [C].

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [D].

  10. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, the system is normal.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

Tip:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P003373)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.

      Powertrain > Engine > Trouble Codes

      Result

      Result

      Proceed to

      DTC P003373 is output

      A

      DTC P003373 and other DTCs are output

      B
      Tip:

      If any DTCs other than P003373 are output, troubleshoot those DTCs first.

    B

    GO TO DTC CHART

    Click hereClick hereClick here

    A

  2. PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR BYPASS VALVE)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Activate the Air Bypass Valve / Data List / All Data / Air Bypass Valve Control.

      Powertrain > Engine > Active Test

      Active Test Display

      Activate the Air Bypass Valve

      Data List Display

      Air Bypass Valve Control

    5. According to the display on the GTS, perform the Active Test and check the operation and operation sound of the air by-pass valve.

      OK

      Active Test

      Standard

      ON

      • ON is displayed for Data List item "Air Bypass Valve Control"

      • Air by-pass valve operates (operation sound is normal)

    Result

    Proceed to

    OK

    NG
    NG

    INSPECT AIR BY-PASS VALVEClick here

    OK

  3. INSPECT NO. 1 TURBO PRESSURE SENSOR

    1. Inspect the No. 1 turbo pressure sensor.

      Click here

    Result

    Proceed to

    OK

    NG
    OK

    CHECK WHETHER DTC OUTPUT RECURS (P003373)Click here

    NG

  4. CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 TURBO PRESSURE SENSOR)

    A347474C10

    *a

    Front view of wire harness connector

    (to No. 1 Turbo Pressure Sensor)

    1. Disconnect the No. 1 turbo pressure sensor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      B192-3 (VC) - B192-2 (E2)

      Ignition switch ON

      4.75 to 5.25 V

      B192-1 (PIM) - B192-2 (E2)

      Ignition switch ON

      3.0 to 5.25 V

    Result

    Proceed to

    OK

    NG
    NG

    CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)Click here

    OK

  5. REPLACE NO. 1 TURBO PRESSURE SENSOR

    1. Replace the No. 1 turbo pressure sensor.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  6. CHECK WHETHER DTC OUTPUT RECURS (P003373)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTC.

      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine / Trouble Codes.

    11. Read the DTCs.

      Powertrain > Engine > Trouble Codes

    Result

    Result

    Proceed to

    DTC P003373 is output

    A

    DTCs are not output

    B
    B

    END

    A

  7. INSPECT AIR BY-PASS VALVE

    1. Inspect the air by-pass valve.

      Click here

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE TURBOCHARGER SUB-ASSEMBLY

    Click hereClick here

    OK

  8. CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR BY-PASS VALVE)

    A346377C05

    *a

    Front view of wire harness connector (to Air By-pass Valve)

    1. Disconnect the air by-pass valve connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      B202-1 - Body ground

      Ignition switch ON

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN RELAY - AIR BY-PASS VALVE)

    OK

  9. CHECK HARNESS AND CONNECTOR (AIR BY-PASS VALVE - ECM)

    1. Disconnect the air by-pass valve connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B202-2 - B208-67 (ABV)

      Always

      Below 1 Ω

      B202-2 or B208-67 (ABV) - Body ground and other terminals

      Always

      10 kΩ or higher

      Result

      Proceed to

      OK

      NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK WHETHER DTC OUTPUT RECURS (P003373)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTC.

      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine / Trouble Codes.

    11. Read the DTCs.

      Powertrain > Engine > Trouble Codes

    Result

    Result

    Proceed to

    DTC P003373 is output

    A

    DTCs are not output

    B
    A

    REPLACE ECM

    Click hereClick here

    B

    CHECK FOR INTERMITTENT PROBLEMS

    Click here

  11. CHECK HARNESS AND CONNECTOR (NO. 1 TURBO PRESSURE SENSOR - ECM)

    1. Disconnect the No. 1 turbo pressure sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B192-3 (VC) - B208-140 (VPTA)

      Always

      Below 1 Ω

      B192-2 (E2) - B208-139 (EPTA)

      Always

      Below 1 Ω

      B192-1 (PIM) - B208-108 (PTA)

      Always

      Below 1 Ω

      B192-3 (VC) or B208-140 (VPTA) - Body ground and other terminals

      Always

      10 kΩ or higher

      B192-1 (PIM) or B208-108 (PTA) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE ECM

    Click hereClick here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR