ULTRASONIC SENSOR(for Rear) INSTALLATION

PROCEDURE


  1. INSTALL NO. 4 ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the No. 4 ultrasonic sensor retainer is necessary.

    • If a No. 4 ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 4 ultrasonic sensor with a new No. 4 ultrasonic sensor retainer as a set to the rear bumper cover.

    • Use the same procedure for all No. 4 ultrasonic sensor retainers.


    1. B007X7U

      Engage the 2 claws to install a new No. 4 ultrasonic sensor retainer to the No. 4 ultrasonic sensor.

    2. Clean the surface of the rear bumper cover.


      1. Remove any remaining double-sided tape from the rear bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    3. B007YDWC01
      *a 19 mm (0.748 in.)

      Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.

    4. B007YDLC02
      B007Z9Y Primer

      Using a brush or felt, apply primer or equivalent to the No. 4 ultrasonic sensor retainer installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    5. Peel off the release paper from the No. 4 ultrasonic sensor retainer.

    6. B007Z1EC02
      *a Protrusion of the mark
      B007ZL6 Press area

      Align the No. 4 ultrasonic sensor retainer with the mark on the rear bumper cover and install it as shown in the illustration.

      Note

      The double-sided tape of a No. 4 ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new No. 4 ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips


      • Align the connector with the protrusion of the mark when connecting it.

      • Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the No. 4 ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the No. 4 ultrasonic sensor retainer and rear bumper cover.

  2. INSTALL NO. 3 ULTRASONIC SENSOR RETAINER

    Tech Tips


    • Perform this procedure only when replacement of the No. 3 ultrasonic sensor retainer is necessary.

    • If a No. 3 ultrasonic sensor retainer has been removed, replace it with a new one.

    • Use the same procedure for all No. 3 ultrasonic sensor retainers.


    1. Clean the surface of the rear bumper cover.


      1. Remove any remaining double-sided tape from the rear bumper cover.

      2. Wipe off any adhesive residue with cleaner.

    2. B007YDWC01
      *a 24 mm (0.945 in.)

      Cover the sensor installation hole with a 24 mm (0.945 in.) circular piece of tape.

    3. B007ZWXC01
      B007Z9Y Primer

      Using a brush or felt, apply primer or equivalent to the No. 3 ultrasonic sensor retainer installation area.

      Note


      • Use a clean brush or felt.

      • Do not touch the rear bumper assembly until the primer has dried.

    4. Peel off the release paper from the No. 3 ultrasonic sensor retainer.

    5. B007WMEC02
      B007ZL6 Press area

      Align the No. 3 ultrasonic sensor retainer with the mark on the rear bumper cover and install it as shown in the illustration.

      Note

      The double-sided tape of a No. 3 ultrasonic sensor retainer will deteriorate if it is detached. Make sure to use a new No. 3 ultrasonic sensor retainer when reattachment is necessary.

      Tech Tips

      Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the No. 3 ultrasonic sensor retainer to the rear bumper cover. Confirm there is no clearance between the No. 3 ultrasonic sensor retainer and rear bumper cover.

  3. INSTALL NO. 4 ULTRASONIC SENSOR


    1. B007YC3C01
      *a Protrusion of the mark
      B007Z37 Install in this Direction

      Engage the 2 claws to install the No. 4 ultrasonic sensor as shown in the illustration.

      Tech Tips


      • Align the connector with the protrusion of the mark when connecting it.

      • Use the same procedure for the RH side and LH side.

    2. Connect the connector.

    3. B007XY9C01
      B007Z37 Install in this Direction

      Engage the 4 claws to install the ultrasonic sensor clip as shown in the illustration.

    4. Engage the clamp.

  4. INSTALL NO. 3 ULTRASONIC SENSOR


    1. B007YHOC03
      *a Protrusion of the mark
      B007Z37 Install in this Direction

      Engage the 2 claws to install the No. 3 ultrasonic sensor as shown in the illustration.

      Tech Tips


      • Align the connector with the protrusion of the mark when connecting it.

      • The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.

    2. Connect the connector.

    3. B007YO5C03
      B007Z37 Install in this Direction

      Engage the 4 claws to install the ultrasonic sensor clip as shown in the illustration.

      Tech Tips

      The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.

    4. Engage the clamp.

  5. INSTALL REAR BUMPER ASSEMBLY

    Click here

  6. PERFORM CALIBRATION (w/o Intelligent Clearance Sonar System)

    Click here

  7. PERFORM CALIBRATION (w/ Intelligent Clearance Sonar System)

    Click here

    SST
    09989-00020