AUTOMATIC TRANSMISSION ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | w/ GPF | - | - |
| *1 | AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1) | *2 | AIR FUEL RATIO SENSOR (for Bank 1 Sensor 2) |
| *3 | AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1) | *4 | AIR FUEL RATIO SENSOR (for Bank 2 Sensor 2) |
| *5 | CONVERTER ASSEMBLY LH | *6 | CONVERTER ASSEMBLY RH |
| *7 | ENGINE ASSEMBLY WITH TRANSMISSION | *8 | ENGINE REAR MOUNTING MEMBER |
| *9 | FLYWHEEL HOUSING SIDE COVER | *10 | FLYWHEEL HOUSING SIDE STAY |
| *11 | FRONT ENGINE MOUNTING INSULATOR | *12 | FRONT FRAME ASSEMBLY |
| *13 | FRONT NO. 1 ENGINE MOUNTING BRACKET RH | *14 | FRONT PROPELLER SHAFT ASSEMBLY |
| *15 | NO. 1 VACUUM PIPE | *16 | NO. 2 ENGINE WIRE |
| *17 | NO. 2 TURBO INSULATOR | *18 | NO. 2 VACUUM PIPE |
| *19 | NO. 4 TURBO INSULATOR | *20 | PROPELLER SHAFT HEAT INSULATOR |
| *21 | REAR ENGINE MOUNTING INSULATOR | *22 | STARTER ASSEMBLY |
| *23 | STARTER COVER | *24 | TURBINE OUTLET ELBOW GUSKET LH |
| *25 | TURBINE OUTLET ELBOW GASKET RH | *26 | EXHAUST PIPE CLAMP LH |
| *27 | EXHAUST PIPE CLAMP RH | *28 | THROTTLE LINK CONNECTING ROD ASSEMBLY |
| *29 | UNIVERSAL JOINT WASHER | *30 | SPRING WASHER |
| *31 | VACUUM TRANSMITTING HOSE ASSEMBLY | *32 | NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |  |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with SST | ● | Non-reusable part |
 |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER | *2 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
| *3 | OIL COOLER TUBE WITH OIL COOLER HOSE | *4 | TORQUE CONVERTER ASSEMBLY |
| *5 | TRANSFER ASSEMBLY | *6 | TRANSMISSION DYNAMIC DAMPER ASSEMBLY LH |
| *7 | TRANSMISSION DYNAMIC DAMPER ASSEMBLY RH | *8 | WIRE HARNESS |
| *9 | TRANSMISSION DYNAMIC DAMPER BRACKET RH | *10 | TRANSMISSION DYNAMIC DAMPER BRACKET LH |
| *11 | TRANSMISSION DYNAMIC DAMPER INSULATOR | *12 | TRANSMISSION DYNAMIC DAMPER |
| *13 | STUD BOLT | - | - |
| *a | Black x 1 Silver x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Clutch spline grease |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | AUTOMATIC TRANSMISSION ASSEMBLY WITH TRANSFER | *2 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
| *3 | OIL COOLER TUBE WITH OIL COOLER HOSE | *4 | TORQUE CONVERTER ASSEMBLY |
| *5 | TRANSFER ASSEMBLY | *6 | TRANSMISSION DYNAMIC DAMPER ASSEMBLY RH |
| *7 | WIRE HARNESS | *8 | TRANSMISSION DYNAMIC DAMPER BRACKET RH |
| *9 | TRANSMISSION DYNAMIC DAMPER INSULATOR | *10 | TRANSMISSION DYNAMIC DAMPER |
| *11 | STUD BOLT | - | - |
| *a | Black x 1 Silver x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | |
Clutch spline grease |