REAR BUMPER(w/ Rear No. 2 Seat) REASSEMBLY

PROCEDURE


  1. INSTALL REAR BUMPER UPPER RETAINER LH


    1. B007ZNAC01
      B007Z37 Install in this Direction

      Engage the 2 guides as shown in the illustration to install the rear bumper upper retainer LH to the rear combination light assembly LH.

    2. Engage the grommet.

    3. B007Z9NC01
      *a Guide
      *b Pin
      B007Z37 Install in this Direction

      Engage the guide and pin as shown in the illustration.

    4. Install the rear bumper upper retainer LH with rear combination light assembly LH with the screw.

  2. INSTALL REAR BUMPER UPPER RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

    Click here

  4. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. INSTALL NO. 1 REAR BUMPER REINFORCEMENT


    1. B005LJ5

      Install the No. 1 rear bumper reinforcement with the 6 nuts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  6. INSTALL REAR BUMPER ENERGY ABSORBER


    1. B007YS4C01
      B007Z37 Install in this Direction

      Engage the 2 guides as shown in the illustration to install the rear bumper energy absorber.

  7. INSTALL REAR BUMPER LOWER RETAINER LH


    1. B007YPDC01
      B007Z37 Install in this Direction

      Engage the claw as shown in the illustration.

    2. B005LQS

      Install the lower rear bumper retainer LH with the 2 screws.

  8. INSTALL REAR BUMPER LOWER RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  9. INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE PROTECTOR COVER


    1. B007WN7C01
      *1 No. 2 Luggage Compartment Side Protector Cover Clip
      B007Z37 Install in this Direction

      Engage the 2 No. 2 luggage compartment side protector cover clips.

    2. Install the No. 2 luggage compartment side protector cover with the clip.

  10. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE PROTECTOR COVER


    1. B007XT2C01
      B007WXX Bolt
      B00803L Clip

      Install the No. 1 luggage compartment side protector cover with the bolt and clip.

  11. CONNECT REAR WHEEL HOUSE LINER LH


    1. B005MJV

      Connect the rear wheel house liner LH with the 2 screws and grommet.

  12. CONNECT REAR WHEEL HOUSE LINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. INSTALL REAR BUMPER SIDE RETAINER LH


    1. B007YL3C01
      B007Z37 Install in this Direction

      Engage the 2 claws as shown in the illustration.

    2. B007WX6C01
      B007Z37 Install in this Direction

      Engage the 3 clips as shown in the illustration to install the rear bumper side retainer LH.

  14. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  15. INSTALL REAR BUMPER MOULDING


    1. B007XWIC01
      B007Z37 Install in this Direction

      Engage the guide and 5 claws as shown in the illustration.

    2. B005Q4G

      Install the rear bumper moulding with the screw.

  16. INSTALL REAR BUMPER SIDE MOULDING LH


    1. B007ZZTC01
      B007Z37 Install in this Direction

      Engage the 2 guides and 3 claws as shown in the illustration.

    2. B005OCB

      Install the rear bumper side moulding LH with the 2 screws.

  17. INSTALL REAR BUMPER SIDE MOULDING RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. INSTALL REAR BUMPER PLATE RH


    1. B007WWAC01
      B007Z37 Install in this Direction

      Engage the claw as shown in the illustration.

    2. B005L7Q

      Install the rear bumper plate RH with the 2 clips.

  19. INSTALL REAR BUMPER SIDE SEAL LH


    1. B007ZB6C01
      B007Z37 Install in this Direction

      Engage the 3 claws as shown in the illustration to install the rear bumper side seal LH.

  20. INSTALL REAR BUMPER SIDE SEAL RH

    Tech Tips

    Use the same procedure as for the LH side.

  21. INSTALL REAR BUMPER PAD

    Tech Tips

    When installing the rear bumper pad, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 40 to 60°C (104 to 140°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove the double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from a new rear bumper pad.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B007Y4VC01
      *a Line

      Install the rear bumper pad as shown in the illustration.

      Tech Tips


      • Install the rear bumper pad along the line on the rear bumper cover.

      • Use the same procedure for the RH side and LH side.

  22. INSTALL REAR BUMPER PROTECTOR

    Tech Tips

    When installing the rear bumper protector, heat the rear bumper assembly using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 40 to 60°C (104 to 140°F)

    Note

    Do not heat the rear bumper assembly excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove the double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from 2 new rear bumper protectors.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. B007X1PC01
      *a Line

      Install the 2 rear bumper protectors as shown in the illustration.

      Tech Tips

      Install the rear bumper protectors along the line on the rear bumper cover.

  23. INSTALL REAR BUMPER LOWER COVER


    1. Engage the 7 guides and 7 claws as shown in the illustration.

      B007ZXCC01
      B007Z37 Install in this Direction - -

    2. Install the rear bumper lower cover with the 2 screws and 13 clips.

      B005OCC

  24. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. B007WL3C01
      B007Z37 Install in this Direction

      Engage the 2 claws as shown in the illustration.

    2. B005MGY

      Install the reflex reflector assembly LH with the screw.

  25. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  26. INSTALL ULTRASONIC SENSOR CLIP (w/ LEXUS Parking Assist-sensor System)

    Tech Tips

    When installing the ultrasonic sensor clip, heat the rear bumper assembly and ultrasonic sensor clip using a heat light.

    Heating Temperature
    Item Temperature
    Rear Bumper Assembly 40 to 60°C (104 to 140°F)
    Ultrasonic Sensor Clip 20 to 30°C (68 to 86°F)

    Note

    Do not heat the rear bumper assembly or ultrasonic sensor clip excessively.


    1. Clean the rear bumper assembly surface.


      1. Using a heat light, heat the rear bumper assembly surface.

      2. Remove the double-sided tape from the rear bumper assembly.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Using a heat light, heat the rear bumper assembly and ultrasonic sensor clip.

    3. Remove the release paper from the 3 new ultrasonic sensor clips.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    4. B007Z6KC01
      *a Line

      Install the 3 ultrasonic sensor clips as shown in the illustration.

      Tech Tips

      Install the ultrasonic sensor clip along the line on the rear bumper cover.

  27. INSTALL NO. 3 LUGGAGE ROOM WIRE (w/ LEXUS Parking Assist-sensor System)


    1. B005LG5

      Engage the 3 clamps to install the No. 3 luggage room wire.

  28. INSTALL NO. 4 ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  29. INSTALL NO. 3 ULTRASONIC SENSOR RETAINER (w/ LEXUS Parking Assist-sensor System)

    Click here

  30. INSTALL NO. 4 ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here

  31. INSTALL NO. 3 ULTRASONIC SENSOR (w/ LEXUS Parking Assist-sensor System)

    Click here