EXHAUST MANIFOLD W/ TURBOCHARGER INSTALLATION

PROCEDURE


  1. INSTALL STUD BOLT

    Note

    If a stud bolt is deformed or its threads are damaged, replace it.


    1. B00253L

      Using an E10 "TORX" socket wrench, install the 3 stud bolts at the positions shown in the illustration.

      Torque:
      14.7 N*m  { 150 kgf*cm, 11 ft.*lbf }
    2. B00246M

      Using an E8 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
    3. B00283C

      Using an E5 "TORX" socket wrench, install the 4 stud bolts at the positions shown in the illustration.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  2. INSTALL COMPRESSOR OUTLET ELBOW


    1. except Cold Specification Vehicles:

      Install the hose clamp with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Install a new gasket.

    3. Install a new gasket and the compressor outlet elbow with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  3. INSTALL COMPRESSOR INLET ELBOW


    1. Using an E8 "TORX" socket wrench, install a new gasket and the compressor inlet elbow with the stud bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    2. Install the compressor inlet elbow to the turbocharger sub-assembly with the 2 nuts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    3. Install the compressor inlet elbow stay with the 2 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  4. INSTALL NO. 1 TURBO WATER PIPE SUB-ASSEMBLY


    1. Install a new gasket.

    2. Temporarily install the turbo water pipe sub-assembly with the bolt and 2 nuts.

    3. Tighten the bolt and 2 nuts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

    4. Connect the No. 1 turbo water hose and No. 2 turbo water hose to the No. 1 turbo water pipe sub-assembly and slide the 2 hose clips to secure the hoses.

  5. TEMPORARILY INSTALL TURBO OIL INLET PIPE SUB-ASSEMBLY


    1. B00255ZC01
      *a NG
      *b OK

      Install a new gasket as shown in the illustration.

      Note

      Do not install the gasket upside down.

    2. Temporarily install the turbo oil inlet pipe sub-assembly with the 2 nuts.

  6. TEMPORARILY INSTALL EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY


    1. Install 2 new gaskets to the exhaust manifold and turbocharger sub-assembly.

    2. Temporarily install the exhaust manifold to turbocharger sub-assembly with 3 new nuts.

    3. B00262WC01
      *A w/ DPF
      *B w/o DPF
      *1 Collar
      B006964 Engine Side

      Temporarily install the exhaust manifold with turbocharger sub-assembly, 8 collars and the 8 plate washers to the cylinder head sub-assembly with 8 new nuts.

      Note

      Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.

    4. Install a new gasket on the union bolt side to turbo oil inlet pipe sub-assembly.

    5. Temporarily install the union bolt.

  7. INSTALL TURBO OIL OUTLET PIPE


    1. Install a new gasket to the turbo oil outlet pipe.

      Note

      The claws of the gasket must face the turbo oil outlet pipe.

    2. Install the turbo oil outlet pipe with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    3. Connect the turbo oil outlet hose to the turbo oil outlet pipe, turbo oil inlet pipe and slide the 2 hose clips to secure the hoses.

  8. TEMPORARILY INSTALL TURBOCHARGER STAY


    1. Temporarily install the turbocharger stay to the turbocharger sub-assembly, with 3 bolts and nut.

  9. TIGHTEN EXHAUST MANIFOLD WITH TURBOCHARGER SUB-ASSEMBLY


    1. B0027NVC01
      *A w/ DPF
      *B w/o DPF

      Tighten the exhaust manifold with turbocharger sub-assembly, to the cylinder head sub-assembly with 8 nuts.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

      Tech Tips

      Tighten the nuts in the order shown in the illustration.

    2. Tighten the turbocharger sub-assembly, to the exhaust manifold with the 3 nuts.

      Torque:
      73 N*m  { 744 kgf*cm, 54 ft.*lbf }

    3. Tighten the 2 nuts and then union bolt of the turbo oil inlet pipe sub-assembly.

      Torque:
      for nut
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }
      for union bolt
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

      Note

      If the connecting part of the union bolt gasket is cracked, remove the connecting part.

  10. TIGHTEN TURBOCHARGER STAY


    1. B0028VCE01

      Tighten the 3 bolts and nut of the turbocharger stay in the order shown in the illustration.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  11. INSTALL NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)


    1. Temporarily install the No. 1 viscous heater bracket sub-assembly with 4 bolts.

    2. B0025JPE01

      Tighten the 4 bolts and of the No. 1 viscous heater bracket sub-assembly in the order shown in the illustration.

      Torque:
      24.5 N*m  { 250 kgf*cm, 18 ft.*lbf }

  12. INSTALL WIRE HARNESS CLAMP BRACKET (for Manual Transmission)


    1. w/o DPF:

      Connect the wire harness with the bolt.

      Torque:
      18.6 N*m  { 190 kgf*cm, 14 ft.*lbf }

    2. w/ DPF:

      Connect the wire harness clamp and install the bolt.

      Torque:
      18.6 N*m  { 190 kgf*cm, 14 ft.*lbf }

    3. w/ DPF:

      for Automatic Transmission:

      Connect the oil cooler tube bracket with the bolt.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

  13. INSTALL OIL COOLER TUBE BRACKET AND WIRE HARNESS CLAMP BRACKET (for Automatic Transmission)


    1. w/o DPF:

      Connect the wire harness with the bolt.

      Torque:
      18.6 N*m  { 190 kgf*cm, 14 ft.*lbf }

    2. w/ DPF:

      Attach the 2 wire harness clamps and connect the wire harness.

    3. for Automatic Transmission:

      Connect the oil cooler tube bracket with the bolt.

      Torque:
      13.5 N*m  { 138 kgf*cm, 10 ft.*lbf }

  14. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

    Click here

  15. CONNECT TURBO WATER HOSE


    1. Connect the No. 1 turbo water hose and No. 2 turbo water hose to the water outlet sub-assembly, engine water pump assembly and slide the 2 hose clips to secure the hoses.

      Note

      The turbocharger sub-assembly may be damaged if the No. 1 turbo water hose and No. 2 turbo water hose are connected to the wrong locations.

  16. INSTALL NO. 1 WATER BY-PASS PIPE

    Click here

  17. INSTALL PCV HOSE (except Cold Area Specification Vehicles)


    1. Attach the clamp and install the PCV hose.

    2. Slide the 2 hose clips to secure the hoses.

  18. INSTALL PCV PIPE (for Cold Area Specification Vehicles)


    1. Connect the PCV pipe to the compressor inlet elbow, cylinder head cover sub-assembly and slide the 2 hose clips to secure the hoses.

    2. Install the PCV pipe with the bolt to the compressor outlet elbow.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    3. Connect the No. 19 water by-pass hose to the compressor inlet elbow and slide the hose clip to secure the hoses.

    4. Install the No. 20 water by-pass hose to the PCV pipe and No. 1 water by-pass pipe, and slide the 2 hose clips to secure the hoses.

  19. INSTALL NO. 3 WATER BY-PASS PIPE


    1. Connect the 2 water hoses to the oil cooler assembly and No. 2 water by-pass pipe, and slide the 2 hose clips to secure the hoses.

    2. Install the No. 3 water by-pass pipe with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    3. for Cold Specification Vehicles:

      Install the water hose to the compressor inlet elbow and No. 3 water by-pass pipe, and slide the 2 hose clips to secure the hoses.

  20. INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

    Click here

  21. INSTALL WATER HOSE SUB-ASSEMBLY (w/ Viscous Heater)

    Click here

  22. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. Install the air cleaner case sub-assembly with the 3 bolts.

      Torque:
      6.0 N*m  { 61 kgf*cm, 53 in.*lbf }

    2. Connect the 3 wire harness clamps.

  23. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY


    1. Install the air cleaner filter element sub-assembly to the air cleaner case.

  24. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE


    1. Attach the 4 clips to install the air cleaner cap sub-assembly with air cleaner hose.

    2. Tighten the hose clamp.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }

    3. Connect the mass air flow meter connector and attach the 2 wire harness clamps.

  25. INSTALL FAN SHROUD

    Click here

  26. INSTALL RADIATOR RESERVOIR

    Click here

  27. INSTALL NO. 1 OIL RESERVOIR BRACKET

    Click here

  28. CONNECT VANE PUMP OIL RESERVOIR ASSEMBLY

    Click here

  29. INSTALL NO. 1 RADIATOR HOSE

    Click here

  30. INSTALL NO. 2 AIR TUBE

    Click here

  31. INSTALL NO. 4 AIR HOSE

    Click here

  32. INSTALL NO. 1 AIR HOSE

    Click here

  33. INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY


  34. ADD ENGINE OIL

    Click here

  35. ADD ENGINE COOLANT

    Click here

  36. INSPECT FOR COOLANT LEAK

    Click here

  37. INSPECT FOR OIL LEAK

    Click here

  38. INSPECT ENGINE OIL LEVEL

    Click here

  39. INSPECT FOR EXHAUST GAS LEAK

    Click here

  40. INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

    Click here

  41. PERFORM INITIALIZATION

    Click here