MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
*A |
w/o Stop and Start System |
*B |
w/ Stop and Start System |
*1 |
BACK-UP LIGHT SWITCH ASSEMBLY |
*2 |
BREATHER PLUG |
*3 |
CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
*4 |
CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
*5 |
CONTROL CABLE BRACKET ASSEMBLY |
*6 |
MANUAL TRANSMISSION DRAIN PLUG |
*7 |
MANUAL TRANSMISSION FILLER PLUG |
*8 |
NEUTRAL POSITION SWITCH |
*9 |
RELEASE CYLINDER BLEEDER PLUG |
*10 |
RELEASE CYLINDER BLEEDER PLUG CAP |
*11 |
TRANSMISSION CASE PLUG |
*12 |
MANUAL TRANSAXLE ASSEMBLY |
*13 |
BLEEDER CLUTCH RELEASE TUBE |
*14 |
GASKET |
*15 |
CLUTCH BOOT TUBE |
- |
- |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
Clutch spline grease |
- |
- |
ILLUSTRATION
*1 |
LOCK BALL PIN |
*2 |
MANUAL TRANSMISSION CASE |
*3 |
OUTER SHIFT LEVER E-RING |
*4 |
REVERSE IDLER GEAR SHAFT BOLT |
*5 |
SHIFT DETENT BALL |
*6 |
STRAIGHT PIN |
*7 |
SHIFT DETENT BALL COMPRESSION SPRING |
*8 |
SHIFT DETENT BALL PLUG |
*9 |
SHIFT AND SELECT LEVER SHAFT STRAIGHT SCREW WITH HEAD PLUG |
*10 |
SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING |
*11 |
FRONT TRANSAXLE CASE |
*12 |
GASKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |
ILLUSTRATION
*1 |
DIFFERENTIAL CASE ASSEMBLY |
*2 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
*3 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
*4 |
INPUT SHAFT ASSEMBLY |
*5 |
OUTER SELECT LEVER |
*6 |
OUTER SELECT LEVER OIL SEAL |
*7 |
REVERSE IDLER GEAR SUB-ASSEMBLY |
*8 |
REVERSE SHIFT ARM BRACKET ASSEMBLY |
*9 |
REVERSE SHIFT FORK |
*10 |
REVERSE SHIFT FORK SHAFT ASSEMBLY |
*11 |
SHIFT AND SELECT LEVER SHAFT ASSEMBLY |
*12 |
SHIFT INTERLOCK PLATE |
*13 |
INNER SELECT LEVER |
*14 |
INNER SELECT LEVER BOLT |
*15 |
REVERSE SHIFT FORK SLOTTED SPRING PIN |
*16 |
REVERSE IDLER THRUST WASHER |
*17 |
REVERSE IDLER GEAR SHAFT |
*18 |
NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY |
*19 |
NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY |
*20 |
OUTPUT SHAFT ASSEMBLY |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
★ |
Precoated part |
ILLUSTRATION
*1 |
FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
*2 |
FRONT OUTPUT SHAFT BEARING |
*3 |
FRONT TRANSAXLE CASE OIL SEAL |
*4 |
TRANSAXLE CASE OIL SEAL |
*5 |
TRANSMISSION MAGNET |
*6 |
FRONT DIFFERENTIAL OIL BAFFLE |
*7 |
FRONT TRANSAXLE CASE |
*8 |
OUTPUT SHAFT COVER |
● |
Non-reusable part |
|
MP grease |
ILLUSTRATION
*1 |
FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING |
*2 |
INPUT SHAFT COVER |
*3 |
MANUAL TRANSMISSION CASE |
*4 |
NO. 1 OIL RECEIVER PIPE |
*5 |
OUTER NO. 1 SHIFT LEVER |
*6 |
OUTER SHIFT LEVER OIL SEAL |
*7 |
REAR INPUT SHAFT BEARING SHIM |
*8 |
REAR OUTPUT SHAFT BEARING |
*9 |
TRANSMISSION CASE OIL SEAL |
*10 |
OUTER SHIFT LEVER SPACER |
*11 |
INNER SHIFT LEVER SLOTTED SPRING PIN |
*12 |
INNER NO. 1 SHIFT LEVER |
*13 |
FRONT DIFFERENTIAL CASE REAR SHIM |
*14 |
REAR OUTPUT SHAFT BEARING SHIM |
● |
Non-reusable part |
|
MP grease |