ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | AIR CLEANER WITH AIR CLEANER HOSE | *2 | NO. 1 AIR CLEANER INLET |
| *3 | NO. 1 ENGINE UNDER COVER ASSEMBLY | *4 | NO. 2 ENGINE UNDER COVER ASSEMBLY |
| *5 | RADIATOR SUPPORT TO CROSS MEMBER BRACE SUB-ASSEMBLY LH | *6 | RADIATOR SUPPORT TO CROSS MEMBER BRACE SUB-ASSEMBLY RH |
| *7 | RADIATOR COVER PLATE | *8 | STRUT BAR BRACKET SUPPORT SUB-ASSEMBLY |
| *9 | V-BANK COVER SUB-ASSEMBLY | *10 | LOWER RADIATOR AIR DEFLECTOR |
| *11 | TRANSMISSION UNDER COVER | *12 | FRONT SUSPENSION MEMBER BRACE |
| *13 | UPPER RADIATOR SUPPORT SEAL | *14 | FENDER APRON BRACE SUB-ASSEMBLY LH |
| *15 | FENDER APRON BRACE SUB-ASSEMBLY RH | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *A | w/ In-tank Oil Cooler | *B | for LHD |
| *1 | DISCHARGE HOSE SUB-ASSEMBLY | *2 | NO. 2 FUEL TUBE SUB-ASSEMBLY |
| *3 | FUEL TUBE SUB-ASSEMBLY | *4 | INLET HEATER WATER HOSE |
| *5 | OUTLET HEATER WATER HOSE | *6 | NO. 1 FUEL VAPOR FEED HOSE |
| *7 | NO. 1 RADIATOR HOSE | *8 | UPPER RELAY BLOCK COVER |
| *9 | NO. 3 RADIATOR HOSE | *10 | SUCTION HOSE SUB-ASSEMBLY A |
| *11 | O-RING | *12 | NO. 1 WATER BY-PASS HOSE |
| *13 | NO. 3 TRANSMISSION OIL COOLER HOSE | *14 | NO. 1 OIL COOLER OUTLET HOSE |
| *15 | WATER INLET HOSE | *16 | UNION TO CHECK VALVE HOSE |
| *17 | HEATER ACCESSORY ASSEMBLY (WITH WATER PIPE SUB-ASSEMBLY) | *18 | VACUUM HOSE ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
for HFC-134a (R134a): Compressor oil ND-OIL 8 or equivalent for HFO-1234yf (R1234yf): Compressor oil ND-OIL 12 or equivalent |
- | - |
ILLUSTRATION
| *A | for LHD | - | - |
| *1 | ENGINE WIRE | *2 | NO. 2 ENGINE WIRE |
| *3 | NO. 3 ENGINE WIRE | *4 | NO. 3 ENGINE ROOM WIRE |
| *5 | CONNECTOR HOLDER | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *A | for RHD | - | - |
| *1 | ENGINE WIRE | *2 | NO. 2 ENGINE WIRE |
| *3 | NO. 3 ENGINE WIRE | *4 | NO. 3 ENGINE ROOM WIRE |
| *5 | NO. 10 CONNECTOR HOLDER | *6 | CONNECTOR HOLDER |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | FRONT BUMPER COVER | *2 | NO. 2 FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY |
| *3 | RADIATOR SUPPORT OPENING COVER | *4 | REAR FRAME RAIL SUB-ASSEMBLY LH |
| *5 | REAR FRAME RAIL SUB-ASSEMBLY RH | *6 | RADIATOR SUPPORT EXTENSION LH |
| *7 | RADIATOR SUPPORT EXTENSION RH | *8 | FRONT FENDER LINER LH |
| *9 | FRONT FENDER LINER RH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT SKID CONTROL SENSOR WIRE LH | *2 | STEERING KNUCKLE LH |
| *3 | TIE ROD ASSEMBLY LH | *4 | FRONT DISC BRAKE DUST COVER LH |
| *5 | FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH | *6 | FRONT STABILIZER LINK ASSEMBLY LH |
| *7 | FRONT DISC LH | *8 | FRONT DISC BRAKE CALIPER ASSEMBLY LH |
| *9 | FRONT SHOCK ABSORBER ASSEMBLY LH | *10 | FRONT UPPER NO. 1 SUSPENSION ARM ASSEMBLY LH |
| *11 | FRONT UPPER NO. 2 SUSPENSION ARM ASSEMBLY LH | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | FLOOR BOARD SUB-ASSEMBLY | *2 | FRONT CENTER FLOOR BRACE SUB-ASSEMBLY |
| *3 | NO. 2 FLOOR BOARD SUB-ASSEMBLY | *4 | REAR FLOOR SIDE MEMBER COVER LH |
| *5 | REAR FLOOR SIDE MEMBER COVER RH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | EXHAUST TAIL PIPE LH | *2 | EXHAUST TAILPIPE ASSEMBLY |
| *3 | FRONT EXHAUST PIPE ASSEMBLY | *4 | EXHAUST PIPE SUPPORT |
| *5 | GASKET | *6 | COMPRESSION SPRING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CENTER NO. 1 FLOOR HEAT INSULATOR SUB-ASSEMBLY | *2 | NO. 2 FUEL TANK PROTECTOR |
| *3 | PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY | *4 | CENTER SUPPORT BEARING DAMPER |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Molybdenum Disulphide Lithium Base NLGI NO. 2 |  |
Do not apply lubricants |
ILLUSTRATION
| *1 | ENGINE AND TRANSMISSION ASSEMBLY | *2 | NO. 2 PARKING LOCK RELEASE CABLE ASSEMBLY |
| *3 | REAR LOWER ARM MOUNTING REINFORCEMENT SUB-ASSEMBLY LH | *4 | STEERING SLIDING WITH SHAFT YOKE SUB-ASSEMBLY |
| *5 | REAR LOWER ARM MOUNTING REINFORCEMENT SUB-ASSEMBLY RH | *6 | NO. 2 GROUND WIRE |
| *7 | ENGINE SIDE COVER LH | *8 | ENGINE SIDE COVER RH |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY | *2 | EXHAUST MANIFOLD ASSEMBLY LH |
| *3 | EXHAUST MANIFOLD ASSEMBLY RH | *4 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | ENGINE OIL LEVEL DIPSTICK GUIDE | *2 | AUTOMATIC TRANSMISSION ASSEMBLY |
| *3 | NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE | *4 | REAR ENGINE MOUNTING INSULATOR |
| *5 | REAR ENGINE MOUNTING MEMBER | *6 | WIRE HARNESS |
| *7 | STARTER ASSEMBLY | *8 | FLYWHEEL HOUSING SIDE COVER |
| *9 | ENGINE OIL LEVEL DIPSTICK | *10 | O-RING |
| *11 | NO. 2 PARKING LOCK RELEASE CABLE ASSEMBLY | *12 | WASHER |
| *13 | NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY | *14 | NO. 3 EXHAUST MANIFOLD HEAT INSULATOR |
| *15 | OIL COOLER TUBE WITH OIL COOLER HOSE | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | ENGINE HANGER | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | FRONT ENGINE MOUNTING INSULATOR | *4 | FRONT FRAME CROSSMEMBER SUB-ASSEMBLY |
| *5 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE | *6 | REAR DRIVE PLATE SPACER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | |
Adhesive 1324 |
| ★ | Precoated part | - | - |