CAN COMMUNICATION SYSTEM(for RHD without Central Gateway ECU) Engine Stop and Start ECU Communication Stop Mode

DTC Code DTC Name
Engine Stop and Start ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Engine Stop and Start ECU Communication Stop Mode

Either condition is met:

  • "Stop and Go/Start" is not displayed on "CAN Bus Check".

    Click here

  • Communication system DTCs (DTCs that start with U) that are output correspond to "Engine Stop and Start ECU Communication Stop Mode" in "DTC Combination Table".

    Click hereClick here

  • Power source or inside engine stop and start ECU

  • Engine stop and start ECU CAN branch wire or connector

  • Engine stop and start ECU

WIRING DIAGRAM

C347358E03

CAUTION / NOTICE / HINT

Note:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click hereClick here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

  • After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click hereClick here

Tip:

  • Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

  1. CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU CAN BRANCH WIRE)

    1. C251435C28

      *a

      Rear view of wire harness connector

      (to Engine Stop and Start ECU)

      Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the engine stop and start ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      G87-13 (CANH) - G87-14 (CANL)

      Cable disconnected from negative (-) battery terminal

      54 to 69 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE ENGINE STOP AND START ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

    OK

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY AND BODY GROUND)

    1. Connect the cable to the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click hereClick here

      C347357C01

      *a

      Front view of wire harness connector

      (to Engine Stop and Start ECU)

      -

      -

    2. Disconnect the engine stop and start ECU connectors.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      A86-3 (BIN1) - Body ground

      Always

      9.5 to 14 V

      A86-1 (BIN2) - Body ground

      Always

      9.5 to 14 V

      A66-1 (+B) - Body ground

      Ignition switch ON

      9.5 to 14 V

      G87-21 (IG1) - Body ground

      Ignition switch ON

      9.5 to 14 V

      G87-18 (IG2) - Body ground

      Ignition switch ON

      9.5 to 14 V

      G87-19 (ACC) - Body ground

      Ignition switch ACC

      9.5 to 14 V

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A66-6 (DGND) - Body ground

      Always

      Below 1 Ω

      A86-8 (GND1) - Body ground

      Always

      Below 1 Ω

      A86-2 (GND2) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE ENGINE STOP AND START ECU

    Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR