ENTRY AND START SYSTEM(for Entry Function) OPERATION CHECK


  1. CHECK ENTRY AND START SYSTEM (for Entry Function) OPERATION

    Note

    Make sure that the entry and start system (for Entry Function) has not been canceled before performing this inspection.


    1. Check the entry unlock function (driver door, front passenger door).


      1. Perform a wireless lock operation to lock the door, touch the unlock sensor built into the backside of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlock.

        Tech Tips

        To perform a wireless lock operation, press the lock button of the electrical key transmitter sub-assembly while standing near the front door outside handle assembly.

      2. A005EWFE01
        Text in Illustration
        *A for LHD
        *B for RHD
        *a 0.7 to 1 m (2.30 to 3.28 ft.)

        Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly and approximately 0.7 m (2.30 ft.) from the vehicle as shown in the illustration and check that the LED (red) of the electrical key transmitter sub-assembly blinks.

      3. With the system in unlock standby mode, hold the front door outside handle assembly and check that the door unlock.

        Tech Tips


        • The system is in unlock standby mode when the electrical key transmitter sub-assembly is in the detection area and the key ID code sent by the electrical key transmitter sub-assembly matches the key ID code stored by the certification ECU (smart key ECU assembly).

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.66 ft.) of the front door outside handle assembly.

        • Inspect the front passenger door using the same procedure (Except Driver's Door Only Entry and Start System).

      4. A005BQGE02
        Text in Illustration
        *A for LHD
        *B for RHD
        *a Unlock Sensor (Backside)

        Check the unlock response sensitivity. With the system in unlock standby mode, touch the area shown in the illustration and check that the door unlocks.

        Note

        If the sensor is touched too quickly or released too slowly, the sensor may not react and the door will not unlock.

    2. Check the entry lock function (driver door, front passenger door).

      Note

      If the electrical key transmitter sub-assembly is in the vehicle but outside the detection area (on the instrument panel, in the glove box, on the floor) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.


      1. A005EWFE01
        Text in Illustration
        *A for LHD
        *B for RHD
        *a Approximately 0.3 m (0.98 ft.)

        With the door closed and unlocked, touch the lock sensor of the front door outside handle assembly of the driver door while carrying the electrical key transmitter sub-assembly and check that the door lock.

      2. A005E1IE01
        Text in Illustration
        *A for LHD
        *B for RHD
        *a Lock Sensor

        Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly and approximately 0.3 m (0.98 ft.) from the vehicle as shown in the illustration, touch the lock sensor and check that the door lock.

        Tech Tips


        • As communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.66 ft.) of the front door outside handle assembly, the door may not lock if the lock sensor is touched with the same hand that is holding the electrical key transmitter sub-assembly, etc.

        • If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna may be leaking from the vehicle.

        • Inspect the front passenger door using the same procedure (Except Driver's Door Only Entry and Start System).

        • The door lock operation cannot be performed more than 2 times consecutively.

      3. After the system enters unlock standby mode, touch the unlock sensor on the outside handle within 3 seconds. Check that the door unlocks.

        Note

        The electrical key transmitter sub-assembly may not be able to communicate with the system within a 0.2 m (0.656 ft.) radius of each outside handle.

    3. Check the entry back door unlock function.


      1. A0059VAE01
        Text in Illustration
        *a Approximately 0.7 m (2.30 ft.)

        Perform a wireless lock operation to lock the door, operate the unlock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly and check that the door unlock.

      2. Inspect the entry back door unlock operating range. While standing at the rear of the vehicle, hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the illustration at the same height as the back door opener switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle, press the unlock switch of the back door opener switch assembly and check that the door unlock.

    4. Check the entry back door lock function.

      Note

      If the electrical key transmitter sub-assembly is inside the vehicle and a door lock operation is performed, it is possible that the electrical key transmitter sub-assembly may be locked inside the vehicle.


      1. With the door closed and unlocked, press the lock switch of the back door opener switch assembly while carrying the electrical key transmitter sub-assembly outside of the vehicle and check that the door lock.

      2. A0059VAE01
        Text in Illustration
        *a Approximately 0.3 m (0.98 ft.)

        Inspect the entry back door lock operating range. Hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the illustration at the same height as the top edge of the rear bumper and approximately 0.3 m (0.98 ft.) from the vehicle, press the lock of the back door opener switch assembly and check that the door lock.

        Tech Tips


        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.66 ft.) of the rear bumper.

        • If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna assembly may be leaking from the vehicle.

    5. Check the push start function.


      1. With the power switch off, push the P position switch, depress the brake pedal while carrying the electrical key transmitter sub-assembly and check that the power switch indicator illuminates in green. Then, press the power switch and check that the hybrid control system starts.

      2. With the brake pedal released and the power switch off, press the power switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.

      3. Stop the vehicle, press the power switch and check that the power source mode changes to off (the hybrid control system stops and all electrical systems are off).

      4. A005D4LE01
        Text in Illustration
        *a Inspection Point

        Inspect the push start operating range (front). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid control system can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.66 ft.) of the shift lever.

        Tech Tips

        Perform the inspection for both inspection points.

      5. A005ETVE01
        Text in Illustration
        *a Inspection Point

        Inspect the push start operating range (rear). Place the electrical key transmitter sub-assembly on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the hybrid control system can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.66 ft.) of the center of the rear seat cushion.

        Tech Tips

        Perform the inspection for both inspection points.

      6. A005D0BE01
        Text in Illustration
        *a Inspection Point

        Inspect the push start operating range (luggage). Place the electrical key transmitter sub-assembly at either inspection point and check that the hybrid control system can be started.

        Note


        • Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in the glove box or on the floor.

        • Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.66 ft.) of the center of the luggage compartment.

        Tech Tips

        Perform the inspection for both inspection points.

    6. Check the key lock-in prevention function (vehicle interior).

      Note

      In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.


      1. Turn the power switch off.

      2. Place the electrical key transmitter sub-assembly on a front or rear seat.

      3. Close the door, but make sure the door are unlocked.

      4. Touch a front door lock sensor and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds.

    7. Check the entry cancel function.


      1. Cancel the entry and start system and check that all the functions of the entry and start system (for Entry Function) no longer operate.

        Tech Tips


        • Refer to the following procedures to cancel the entry and start system (for Entry Function) Click here.

        • While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly against the power switch.

      2. While the key cancel function (entry cancel function) is on, check that all functions of the entry and start system cannot be operated.

    8. Check the answer-back function (hazard warning light flashing and buzzer sounding*).

      Entry Operation Wireless Buzzer* Hazard Warning Light
      Entry Door Lock Sounds once Flashes once
      Entry Door Unlock Sounds twice Flashes twice
      Entry Back Door Lock Sounds once Flashes once
      Entry Back Door Unlock Sounds twice Flashes twice

      • *: w/ Wireless Buzzer Answer Back Function

  2. KEY DIAGNOSTIC MODE (Using GTS)

    Tech Tips

    With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.


    1. Enter the following menus: Body Electrical / Entry&Start / Utility / Key Communication Check.

    2. Select a part to inspect from the following table.

      Tester Display Inspection Range
      Overhead + Driver Side*1 Front door outside handle assembly (electrical key antenna) [for Driver Side]
      Overhead + Passenger Side*2 Front door outside handle assembly (electrical key antenna) [for Front Passenger Side]
      Overhead + Front Room*3 No. 1 indoor electrical key antenna assembly (front floor)
      Overhead + Rear Room*4 No. 3 indoor electrical key antenna assembly (rear floor)
      Overhead + Back Door (inside)*5 No. 2 indoor electrical key antenna (inside luggage)
      Overhead + Back Door*6 Electrical key antenna (outside luggage)

    3. Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.

      Tech Tips

      The buzzer sounds in short, repeated beeps for all items except "Overhead + Rear Room"*4. For "Overhead + Rear Room"*4, the buzzer sounds in one long, continuous beep.


      1. A005EWFE01
        Text in Illustration
        *A for LHD
        *B for RHD
        *a Approximately 0.3 m (0.98 ft.)

        *1: Door electrical oscillator (for Driver Side)

        Tech Tips


        • Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly in the position shown in the illustration.

        • *2: Perform the same inspection for the front passenger side (Except Driver's Door Only Entry and Start System).

    4. A005D4LE01
      Text in Illustration
      *a Inspection Point

      *3: No. 1 indoor electrical key antenna assembly (front floor)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.

    5. A005ETVE01
      Text in Illustration
      *a Inspection Point

      *4: No. 3 indoor electrical key antenna assembly (rear floor)

      Tech Tips

      Place the electrical key transmitter sub-assembly on the rear seat cushion.

    6. A005D0BE01
      Text in Illustration
      *a Inspection Point

      *5: No. 2 indoor electrical key antenna (inside luggage)

      Tech Tips

      Place the electrical key transmitter sub-assembly in the luggage compartment. Even if the electrical key transmitter sub-assembly is in the luggage compartment, the buzzer may not sound.

    7. A0059VAE01
      Text in Illustration
      *a Approximately 0.7 m (2.30 ft.)

      *6: Outside electrical key oscillator (outside luggage) (Except Driver's Door Only Entry and Start System)

      Tech Tips

      Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle, as shown in the illustration.