AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) Speaker Circuit

DESCRIPTION

WIRING DIAGRAM

PROCEDURE

1. CONFIRM MODEL

   1. Choose the model to be inspected.

      Result

      Result	Proceed to
      except Sedan	A
      for Sedan (for 4 Speakers, w/o Manual (SOS) Switch)	B
      for Sedan (for 4 Speakers, w/ Manual (SOS) Switch)	C
      for Sedan (for 6 Speakers, w/o Manual (SOS) Switch)	D
      for Sedan (for 6 Speakers, w/ Manual (SOS) Switch)	E

   B

   CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- SPEAKERS)Click here

   C

   CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- TELEMATICS TRANSCEIVER - SPEAKERS)Click here

   D

   CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- SPEAKERS)Click here

   E

   CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- TELEMATICS TRANSCEIVER - SPEAKERS)Click here

   A

2. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- SPEAKERS)

   1. Disconnect the E109 radio receiver assembly connector.

   2. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

   3. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      E109-1 (FR+) - G4-4 (TWR+)	Always	Below 1 Ω
      E109-5 (FR-) - G4-2 (TWR-)	Always	Below 1 Ω
      E109-2 (FL+) - H5-4 (TWL+)	Always	Below 1 Ω
      E109-6 (FL-) - H5-2 (TWL-)	Always	Below 1 Ω
      G4-3 (+) - G1-1	Always	Below 1 Ω
      G4-1 (-) - G1-2	Always	Below 1 Ω
      H5-3 (+) - H1-1	Always	Below 1 Ω
      H5-1 (-) - H1-2	Always	Below 1 Ω
      E109-1 (FR+) or G4-4 (TWR+) - Body ground	Always	10 kΩ or higher
      E109-5 (FR-) or G4-2 (TWR-) - Body ground	Always	10 kΩ or higher
      E109-2 (FL+) or H5-4 (TWL+) - Body ground	Always	10 kΩ or higher
      E109-6 (FL-) or H5-2 (TWL-) - Body ground	Always	10 kΩ or higher
      G4-3 (+) or G1-1 - Body ground	Always	10 kΩ or higher
      G4-1 (-) or G1-2 - Body ground	Always	10 kΩ or higher
      H5-3 (+) or H1-1 - Body ground	Always	10 kΩ or higher
      H5-1 (-) or H1-2 - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

3. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

   1. Remove the front No. 1 speaker assembly.

      Click here

   2. 

      *a	Component without harness connected (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      1 - 2	Always	3.2 to 4.8 Ω

   Result

   Proceed to
   OK
   NG

   NG

   REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

   Click here

   OK

4. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

   1. Remove the front No. 2 speaker assembly.

      Click here

   2. 

      *A	for RH
      *B	for LH
      *a	Component without harness connected (Front No. 2 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

   Standard Resistance

   Table 1. for RH

   Tester Connection	Condition	Specified Condition
   4 (TWR+) - 2 (TWR-)	Always	10 kΩ or higher
   1 (-) - 2 (TWR-)	Always	Below 1 Ω
   3 (+) - 4 (TWR+)	Always	Below 1 Ω

   Table 2. for LH

   Tester Connection	Condition	Specified Condition
   4 (TWL+) - 2 (TWL-)	Always	10 kΩ or higher
   1 (-) - 2 (TWL-)	Always	Below 1 Ω
   3 (+) - 4 (TWL+)	Always	Below 1 Ω

   Result

   Proceed to
   OK
   NG

   NG

   REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

   Click here

   OK

5. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

   1. Check that the malfunction disappears when a known good speaker is installed.

      Click here

      OK

      Malfunction disappears.

      Tip:

      • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

      • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

      • Perform the above inspection on both LH and RH sides.

   Result

   Proceed to
   OK
   NG

   OK

   END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

   NG

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

   Click here

6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- SPEAKERS)

   1. Disconnect the E109 and E110 radio receiver assembly connectors.

   2. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

   3. Disconnect the L79 and L80 rear speaker assembly connectors.

   4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      E109-1 (FR+) - G1-1	Always	Below 1 Ω
      E109-5 (FR-) - G1-2	Always	Below 1 Ω
      E109-2 (FL+) - H1-1	Always	Below 1 Ω
      E109-6 (FL-) - H1-2	Always	Below 1 Ω
      E110-1 (RR+) - L79-1	Always	Below 1 Ω
      E110-3 (RR-) - L79-2	Always	Below 1 Ω
      E110-2 (RL+) - L80-1	Always	Below 1 Ω
      E110-6 (RL-) - L80-2	Always	Below 1 Ω
      E109-1 (FR+) or G1-1 - Body ground	Always	10 kΩ or higher
      E109-5 (FR-) or G1-2 - Body ground	Always	10 kΩ or higher
      E109-2 (FL+) or H1-1 - Body ground	Always	10 kΩ or higher
      E109-6 (FL-) or H1-2 - Body ground	Always	10 kΩ or higher
      E110-1 (RR+) or L79-1 - Body ground	Always	10 kΩ or higher
      E110-3 (RR-) or L79-2 - Body ground	Always	10 kΩ or higher
      E110-2 (RL+) or L80-1 - Body ground	Always	10 kΩ or higher
      E110-6 (RL-) or L80-2 - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

7. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

   1. Remove the front No. 1 speaker assembly.

      Click here

   2. 

      *a	Component without harness connected (Front No. 1 Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      1 - 2	Always	3.2 to 4.8 Ω

   Result

   Proceed to
   OK
   NG

   NG

   REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

   Click here

   OK

8. INSPECT REAR SPEAKER ASSEMBLY

   1. Remove the rear speaker assembly.

      Click here

   2. 

      *a	Component without harness connected (Rear Speaker Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      1 - 2	Always	3.2 to 4.8 Ω

   Result

   Proceed to
   OK
   NG

   OK

   PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

   Click here

   NG

   REPLACE REAR SPEAKER ASSEMBLY

   Click here

9. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- TELEMATICS TRANSCEIVER - SPEAKERS)

   1. Disconnect the E109 and E110 radio receiver assembly connectors.

   2. Disconnect the E143 telematics transceiver connector.

   3. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

   4. Disconnect the L79 and L80 rear speaker assembly connectors.

   5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection	Condition	Specified Condition
      E109-1 (FR+) - E143-2 (SPI+)	Always	Below 1 Ω
      E109-5 (FR-) - E143-3 (SPI-)	Always	Below 1 Ω
      E143-5 (SPO+) - G1-1	Always	Below 1 Ω
      E143-6 (SPO-) - G1-2	Always	Below 1 Ω
      E109-2 (FL+) - H1-1	Always	Below 1 Ω
      E109-6 (FL-) - H1-2	Always	Below 1 Ω
      E110-1 (RR+) - L79-1	Always	Below 1 Ω
      E110-3 (RR-) - L79-2	Always	Below 1 Ω
      E110-2 (RL+) - L80-1	Always	Below 1 Ω
      E110-6 (RL-) - L80-2	Always	Below 1 Ω
      E109-1 (FR+) or E143-2 (SPI+) - Body ground	Always	10 kΩ or higher
      E109-5 (FR-) or E143-3 (SPI-) - Body ground	Always	10 kΩ or higher
      E143-5 (SPO+) or G1-1 - Body ground	Always	10 kΩ or higher
      E143-6 (SPO-) or G1-2 - Body ground	Always	10 kΩ or higher
      E109-2 (FL+) or H1-1 - Body ground	Always	10 kΩ or higher
      E109-6 (FL-) or H1-2 - Body ground	Always	10 kΩ or higher
      E110-1 (RR+) or L79-1 - Body ground	Always	10 kΩ or higher
      E110-3 (RR-) or L79-2 - Body ground	Always	10 kΩ or higher
      E110-2 (RL+) or L80-1 - Body ground	Always	10 kΩ or higher
      E110-6 (RL-) or L80-2 - Body ground	Always	10 kΩ or higher

   Result

   Proceed to
   OK
   NG

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

10. INSPECT TELEMATICS TRANSCEIVER

    1. Remove the telematics transceiver.

       Click here

    2. 

       *a	Component without harness connected (Telematics Transceiver)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       2 (SPI+) - 5 (SPO+)	Always	Below 1 Ω
       3 (SPI-) - 6 (SPO-)	Always	Below 1 Ω
       2 (SPI+) - 3 (SPI-)	Always	10 kΩ or higher
       5 (SPO+) - 6 (SPO-)	Always	10 kΩ or higher
       2 (SPI+) or 5 (SPO+) - Body ground	Always	10 kΩ or higher
       3 (SPI-) or 6 (SPO-) - Body ground	Always	10 kΩ or higher

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE TELEMATICS TRANSCEIVER

    Click here

    OK

11. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

       Click here

    2. 

       *a	Component without harness connected (Front No. 1 Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       1 - 2	Always	3.2 to 4.8 Ω

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

    OK

12. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

       Click here

    2. 

       *a	Component without harness connected (Rear Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       1 - 2	Always	3.2 to 4.8 Ω

    Result

    Proceed to
    OK
    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY

    Click here

13. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- SPEAKERS)

    1. Disconnect the E109 and E110 radio receiver assembly connectors.

    2. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    3. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    4. Disconnect the L79 and L80 rear speaker assembly connectors.

    5. Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       E109-1 (FR+) - G4-4 (TWR+)	Always	Below 1 Ω
       E109-5 (FR-) - G4-2 (TWR-)	Always	Below 1 Ω
       G4-3 (+) - G1-1	Always	Below 1 Ω
       G4-1 (-) - G1-2	Always	Below 1 Ω
       E109-2 (FL+) - H5-4 (TWL+)	Always	Below 1 Ω
       E109-6 (FL-) - H5-2 (TWL-)	Always	Below 1 Ω
       H5-3 (+) - H1-1	Always	Below 1 Ω
       H5-1 (-) - H1-2	Always	Below 1 Ω
       E110-1 (RR+) - L79-1	Always	Below 1 Ω
       E110-3 (RR-) - L79-2	Always	Below 1 Ω
       E110-2 (RL+) - L80-1	Always	Below 1 Ω
       E110-6 (RL-) - L80-2	Always	Below 1 Ω
       E109-1 (FR+) or G4-4 (TWR+) - Body ground	Always	10 kΩ or higher
       E109-5 (FR-) or G4-2 (TWR-) - Body ground	Always	10 kΩ or higher
       G4-3 (+) or G1-1 - Body ground	Always	10 kΩ or higher
       G4-1 (-) or G1-2 - Body ground	Always	10 kΩ or higher
       E109-2 (FL+) or H5-4 (TWL+) - Body ground	Always	10 kΩ or higher
       E109-6 (FL-) or H5-2 (TWL-) - Body ground	Always	10 kΩ or higher
       H5-3 (+) or H1-1 - Body ground	Always	10 kΩ or higher
       H5-1 (-) or H1-2 - Body ground	Always	10 kΩ or higher
       E110-1 (RR+) or L79-1 - Body ground	Always	10 kΩ or higher
       E110-3 (RR-) or L79-2 - Body ground	Always	10 kΩ or higher
       E110-2 (RL+) or L80-1 - Body ground	Always	10 kΩ or higher
       E110-6 (RL-) or L80-2 - Body ground	Always	10 kΩ or higher

    Result

    Proceed to
    OK
    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

14. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

       Click here

    2. 

       *a	Component without harness connected (Front No. 1 Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       1 - 2	Always	3.2 to 4.8 Ω

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

    OK

15. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

       Click here

    2. 

       *A	for RH
       *B	for LH
       *a	Component without harness connected (Front No. 2 Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

    Standard Resistance

    Table 3. for RH

    Tester Connection	Condition	Specified Condition
    4 (TWR+) - 2 (TWR-)	Always	10 kΩ or higher
    1 (-) - 2 (TWR-)	Always	Below 1 Ω
    3 (+) - 4 (TWR+)	Always	Below 1 Ω

    Table 4. for LH

    Tester Connection	Condition	Specified Condition
    4 (TWL+) - 2 (TWL-)	Always	10 kΩ or higher
    1 (-) - 2 (TWL-)	Always	Below 1 Ω
    3 (+) - 4 (TWL+)	Always	Below 1 Ω

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    Click here

    OK

16. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Check that the malfunction disappears when a known good speaker is installed.

       Click here

       OK

       Malfunction disappears.

       Tip:

       • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

       • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

       • Perform the above inspection on both LH and RH sides.

    Result

    Proceed to
    OK
    NG

    OK

    END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

    NG

17. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

       Click here

    2. 

       *a	Component without harness connected (Rear Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       1 - 2	Always	3.2 to 4.8 Ω

    Result

    Proceed to
    OK
    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY

    Click here

18. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- TELEMATICS TRANSCEIVER - SPEAKERS)

    1. Disconnect the E109 and E110 radio receiver assembly connectors.

    2. Disconnect the E143 telematics transceiver connector.

    3. Disconnect the G1 and H1 front No. 1 speaker assembly connectors.

    4. Disconnect the G4 and H5 front No. 2 speaker assembly connectors.

    5. Disconnect the L79 and L80 rear speaker assembly connectors.

    6. Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       E109-1 (FR+) - E143-2 (SPI+)	Always	Below 1 Ω
       E109-5 (FR-) - E143-3 (SPI-)	Always	Below 1 Ω
       E143-5 (SPO+) - G4-4 (TWR+)	Always	Below 1 Ω
       E143-6 (SPO-) - G4-2 (TWR-)	Always	Below 1 Ω
       G4-3 (+) - G1-1	Always	Below 1 Ω
       G4-1 (-) - G1-2	Always	Below 1 Ω
       E109-2 (FL+) - H5-4 (TWL+)	Always	Below 1 Ω
       E109-6 (FL-) - H5-2 (TWL-)	Always	Below 1 Ω
       H5-3 (+) - H1-1	Always	Below 1 Ω
       H5-1 (-) - H1-2	Always	Below 1 Ω
       E110-1 (RR+) - L79-1	Always	Below 1 Ω
       E110-3 (RR-) - L79-2	Always	Below 1 Ω
       E110-2 (RL+) - L80-1	Always	Below 1 Ω
       E110-6 (RL-) - L80-2	Always	Below 1 Ω
       E109-1 (FR+) or E143-2 (SPI+) - Body ground	Always	10 kΩ or higher
       E109-5 (FR-) or E143-3 (SPI-) - Body ground	Always	10 kΩ or higher
       E143-5 (SPO+) or G4-4 (TWR+) - Body ground	Always	10 kΩ or higher
       E143-6 (SPO-) or G4-2 (TWR-) - Body ground	Always	10 kΩ or higher
       G4-3 (+) or G1-1 - Body ground	Always	10 kΩ or higher
       G4-1 (-) or G1-2 - Body ground	Always	10 kΩ or higher
       E109-2 (FL+) or H5-4 (TWL+) - Body ground	Always	10 kΩ or higher
       E109-6 (FL-) or H5-2 (TWL-) - Body ground	Always	10 kΩ or higher
       H5-3 (+) or H1-1 - Body ground	Always	10 kΩ or higher
       H5-1 (-) or H1-2 - Body ground	Always	10 kΩ or higher
       E110-1 (RR+) or L79-1 - Body ground	Always	10 kΩ or higher
       E110-3 (RR-) or L79-2 - Body ground	Always	10 kΩ or higher
       E110-2 (RL+) or L80-1 - Body ground	Always	10 kΩ or higher
       E110-6 (RL-) or L80-2 - Body ground	Always	10 kΩ or higher

    Result

    Proceed to
    OK
    NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

19. INSPECT TELEMATICS TRANSCEIVER

    1. Remove the telematics transceiver.

       Click here

    2. 

       *a	Component without harness connected (Telematics Transceiver)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       2 (SPI+) - 5 (SPO+)	Always	Below 1 Ω
       3 (SPI-) - 6 (SPO-)	Always	Below 1 Ω
       2 (SPI+) - 3 (SPI-)	Always	10 kΩ or higher
       5 (SPO+) - 6 (SPO-)	Always	10 kΩ or higher
       2 (SPI+) or 5 (SPO+) - Body ground	Always	10 kΩ or higher
       3 (SPI-) or 6 (SPO-) - Body ground	Always	10 kΩ or higher

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE TELEMATICS TRANSCEIVER

    Click here

    OK

20. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

    1. Remove the front No. 1 speaker assembly.

       Click here

    2. 

       *a	Component without harness connected (Front No. 1 Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       1 - 2	Always	3.2 to 4.8 Ω

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

    Click here

    OK

21. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

    1. Remove the front No. 2 speaker assembly.

       Click here

    2. 

       *A	for RH
       *B	for LH
       *a	Component without harness connected (Front No. 2 Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

    Standard Resistance

    Table 5. for RH

    Tester Connection	Condition	Specified Condition
    4 (TWR+) - 2 (TWR-)	Always	10 kΩ or higher
    1 (-) - 2 (TWR-)	Always	Below 1 Ω
    3 (+) - 4 (TWR+)	Always	Below 1 Ω

    Table 6. for LH

    Tester Connection	Condition	Specified Condition
    4 (TWL+) - 2 (TWL-)	Always	10 kΩ or higher
    1 (-) - 2 (TWL-)	Always	Below 1 Ω
    3 (+) - 4 (TWL+)	Always	Below 1 Ω

    Result

    Proceed to
    OK
    NG

    NG

    REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    Click here

    OK

22. REPLACE FRONT NO. 2 SPEAKER ASSEMBLY

    1. Check that the malfunction disappears when a known good speaker is installed.

       Click here

       OK

       Malfunction disappears.

       Tip:

       • Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.

       • When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.

       • Perform the above inspection on both LH and RH sides.

    Result

    Proceed to
    OK
    NG

    OK

    END (FRONT NO. 2 SPEAKER ASSEMBLY WAS DEFECTIVE)

    NG

23. INSPECT REAR SPEAKER ASSEMBLY

    1. Remove the rear speaker assembly.

       Click here

    2. 

       *a	Component without harness connected (Rear Speaker Assembly)

       Measure the resistance according to the value(s) in the table below.

       Standard Resistance

       Tester Connection	Condition	Specified Condition
       1 - 2	Always	3.2 to 4.8 Ω

    Result

    Proceed to
    OK
    NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click here

    NG

    REPLACE REAR SPEAKER ASSEMBLY

    Click here