FRONT DRIVE SHAFT ASSEMBLY DISASSEMBLY

PROCEDURE


  1. SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP


    1. B005XH3

      Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.

  2. SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

    Tech Tips

    Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.

  3. SEPARATE INBOARD JOINT BOOT


    1. Separate the inboard joint boot from the front drive inboard joint assembly.

  4. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY


    1. Remove the old grease from the front drive inboard joint assembly.

    2. B005ZTZE05
      Text in Illustration
      *a Matchmark

      Put matchmarks on the front drive inboard joint assembly and front axle outboard joint shaft assembly.

      Note

      Do not use a punch for the marks.

    3. Remove the front drive inboard joint assembly from the front axle outboard joint shaft assembly.

    4. Secure the front axle outboard joint shaft assembly in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    5. B005ZUZ

      Using a snap ring expander, remove the shaft snap ring from the front axle outboard joint shaft assembly.

    6. B005XIEE29
      Text in Illustration
      *a Matchmark

      Put matchmarks on the front axle outboard joint shaft assembly and tripod joint.

      Note

      Do not use a punch for the marks.

    7. Using a brass bar and a hammer, tap out the tripod joint from the front axle outboard joint shaft assembly.

      Note


      • Do not tap the rollers.

      • Do not drop the tripod joint.

    8. Remove the front No. 2 axle inboard joint boot clamp, inboard joint boot and front axle inboard joint boot clamp.

    9. B005ZG2

      Remove the front axle inboard joint grommet from the front drive inboard joint assembly.

  5. SEPARATE FRONT DRIVE SHAFT DAMPER CLAMP (w/ 1 Clamp)


    1. B005YKUE03
      Text in Illustration
      *A for One Touch Type
      *B for Claw Engagement Type

      for One Touch Type:


      1. Using a screwdriver, release the staked part of the front drive shaft damper clamp and separate the front drive shaft damper clamp as shown in the illustration.

    2. for Claw Engagement Type:


      1. Using needle-nose pliers, disengage the 2 claws and remove the front drive shaft damper clamp as shown in the illustration.

  6. SEPARATE FRONT DRIVE SHAFT DAMPER CLAMP (w/ 2 Clamps)


    1. for Type A:


      1. B005YFTC02
        *A for Type A
        *B for Type B
        *a Claw

        Using needle-nose pliers, disengage each claw on each front drive shaft damper clamp, and then separate each clamp as shown in the illustration.

    2. for Type B:


      1. Using needle-nose pliers, separate the 2 front drive shaft damper clamps as shown in the illustration.

  7. REMOVE FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)


    1. Remove the front drive shaft damper and front drive shaft damper clamp from the front axle outboard joint shaft assembly.

  8. REMOVE FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)


    1. Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front axle outboard joint shaft assembly.

  9. SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)


    1. B005YZW

      Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.

  10. SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

    Tech Tips

    Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.

  11. REMOVE OUTBOARD JOINT BOOT (for LH Side)


    1. Remove the front axle outboard joint boot clamp, outboard joint boot and front No. 2 axle outboard joint boot clamp from the front axle outboard joint shaft assembly.

    2. Remove the old grease from the outboard joint.

  12. REMOVE FRONT DRIVE SHAFT DUST COVER


    1. B005ZHBE40

      Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

      SST
      09950-00020

      Note

      Do not drop the front drive inboard joint assembly.