VEHICLE STABILITY CONTROL SYSTEM Brake Warning Light Remains ON

DTC Code DTC Name
Brake Warning Light Remains ON

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light remains on:

  • The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

  • The brake fluid level is insufficient.

  • The parking brake is applied.

  • EBD operation is not possible.

WIRING DIAGRAM

C334079E01

CAUTION / NOTICE / HINT

Note:

  • When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK CAN COMMUNICATION SYSTEM

    1. Check if CAN communication system DTCs are output.

      Click here

      Result

      Result

      Proceed to

      DTCs are not output.

      A

      DTCs are output.

      B
    B

    INSPECT CAN COMMUNICATION SYSTEM

    Click here

    A

  2. CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

    1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

      OK

      The connector is securely connected.

    Result

    Proceed to

    OK

    NG
    NG

    CONNECT CONNECTOR TO ECU CORRECTLY

    OK

  3. CHECK BATTERY

    1. Check the battery voltage.

      Standard Voltage

      11 to 14 V

    Result

    Proceed to

    OK

    NG
    NG

    CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

    for 1ND-TV:Click here

    for 1NR-FE:Click here

    for 8NR-FTS:Click here

    for 1ZR-FAE:Click here

    for 1ZR-FE:Click here

    for 2ZR-FE:Click here

    for 1WW:Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

    1. C238832C03

      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Disconnect the A97 skid control ECU (brake actuator assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      A97-25 (+BS) - Body ground

      Always

      11 to 14 V

      A97-25 (+BS) - A97-38 (GND1)

      Always

      11 to 14 V

      A97-28 (IG1) - Body ground

      Ignition switch ON

      11 to 14 V

      A97-28 (IG1) - A97-38 (GND1)

      Ignition switch ON

      11 to 14 V

    Result

    Result

    Proceed to

    OK

    A

    NG (w/o Stop and Start System)

    B

    NG (w/ Stop and Start System)

    C
    B

    REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

    C

    INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

    Click here

    A

  5. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

    1. C238832C04

      *a

      Front view of wire harness connector

      (to Skid Control ECU (Brake Actuator Assembly))

      Turn the ignition switch off.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      A97-38 (GND1) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

    OK

  6. READ VALUE USING GTS (PARKING BRAKE SWITCH ASSEMBLY)

    1. Reconnect the A97 skid control ECU (brake actuator assembly) connector.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Select the Data List using the GTS.

      Click here

      Chassis > ABS/VSC/TRC > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      Parking Brake SW

      Parking brake switch

      ON or OFF

      ON: Parking brake applied

      OFF: Parking brake released

      -

      Chassis > ABS/VSC/TRC > Data List

      Tester Display

      Parking Brake SW

    5. Using the GTS, check that the switch condition displayed on the GTS changes according to the parking brake operation.

      OK

      When the parking brake is operated, the display changes as shown above.

    Result

    Result

    Proceed to

    OK (for Sedan)

    A

    OK (for Hatchback, Wagon)

    B

    NG

    C
    B

    INSPECT BRAKE FLUID LEVEL WARNING SWITCHClick here

    C

    INSPECT PARKING BRAKE SWITCH ASSEMBLYClick here

    A

  7. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

    1. C230719C03

      *a

      Component without harness connected

      (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))

      Turn the ignition switch off.

    2. Remove the reservoir filler cap and strainer.

    3. Disconnect the A156 brake fluid level warning switch connector.

    4. Measure the resistance according to the value(s) in the table below.

      Tip:

      A float is located inside the reservoir. Its position changes according to the brake fluid level.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (+) - 2 (E)

      Switch OFF (Float up)

      1.9 to 2.1 kΩ

      1 (+) - 2 (E)

      Switch ON (Float down)

      Below 1 Ω
      Tip:

      If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.

    Result

    Result

    Proceed to

    OK

    A

    NG (for LHD)

    B

    NG (for RHD)

    C
    B

    REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

    Click here

    C

    REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

    Click here

    A

  8. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)

    1. Disconnect the E46 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E46-12 (SW) - A156-1 (+)

      Always

      Below 1 Ω

      E46-12 (SW) or A156-1 (+) - Body ground

      Always

      10 kΩ or higher

      A156-2 (E) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT COMBINATION METER ASSEMBLY

    1. Reconnect the E46 combination meter assembly connector and A61 or A156 brake fluid level warning switch connectors.

    2. Perform an Active Test of the combination meter assembly using the GTS.

      Click here

      Body Electrical > Combination Meter > Active Test

      Tester Display

      Indicat. Lamp Brake

    3. Check the combination meter assembly.

      OK

      The brake warning light turns on or off in accordance with the Active Test operation.

      Tip:

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY

    Click here

    NG

    INSPECT METER / GAUGE SYSTEM

    Click here

  10. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

    1. C304973C01

      *a

      Component without harness connected

      (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))

      Turn the ignition switch off.

    2. Remove the reservoir filler cap and strainer.

    3. Disconnect the A61 brake fluid level warning switch connector.

    4. Measure the resistance according to the value(s) in the table below.

      Tip:

      A float is located inside the reservoir. Its position changes according to the brake fluid level.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (+) - 2 (E)

      Switch OFF (Float up)

      1.9 to 2.1 kΩ

      1 (+) - 2 (E)

      Switch ON (Float down)

      Below 1 Ω
      Tip:

      If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.

    Result

    Result

    Proceed to

    OK

    A

    NG (for LHD)

    B

    NG (for RHD)

    C
    B

    REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

    Click here

    C

    REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

    Click here

    A

  11. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH)

    1. Disconnect the E46 combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      E46-12 (SW) - A61-1 (+)

      Always

      Below 1 Ω

      E46-12 (SW) or A61-1 (+) - Body ground

      Always

      10 kΩ or higher

      A61-2 (E) - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    OK

    INSPECT COMBINATION METER ASSEMBLYClick here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  12. INSPECT PARKING BRAKE SWITCH ASSEMBLY

    1. C211519C03

      *a

      Component without harness connected

      (Parking Brake Switch Assembly)

      Turn the ignition switch off.

    2. Disconnect the L18 parking brake switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      1 (+) - Body ground

      Parking brake switch ON (Switch pin free)

      Below 1 Ω

      1 (+) - Body ground

      Parking brake switch OFF (Switch pin pushed in)

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPLACE PARKING BRAKE SWITCH ASSEMBLY

    Click here

    OK

  13. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY)

    1. Disconnect the 3E main body ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3E-27 (PKB) - L18-1 (+)

      Always

      Below 1 Ω

      3E-27 (PKB) or L18-1 (+) - Body ground

      Always

      10 kΩ or higher
      Tip:

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

      Click here

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    for LHD:Click here

    for RHD:Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR